Bedienungsanleitung Keurig Office Pro B145 (Seite 7 von 26) (Englisch)

562633

Zoom out

Zoom in

Vorherige Seite

1/26

Nächste Seite

Set-Up & First Brew

IMPORTANT: You cannot use your Keurig

brewer until it has been primed for its first use

as set forth below.

Priming your Brewer

1. Unwrap cord and plug the brewer into a

grounded outlet.

2. Ensure Brew/Drain is set to Brew.

3. Place a cup or mug on the Drip Tray Plate.

4. Remove the Water Reservoir from Brewer by

first removing Lid from Reservoir, then lifting

Reservoir straight up and away from Brewer

(may be tight). Rinse with fresh water.

5. Fill Water Reservoir with fresh water so

that the water level reaches the line just

below the top edge of the clear viewing

area. (Be careful not to over fill.)

6. Place Water Reservoir base into the left

side of the Brewer and be sure the

Water Reservoir Lock Tabs engage

with the Brewer. Replace Lid on Water Reservoir.

7. Press Power Button found on upper right

panel of the Brewer. The green light next to

the Power Button will become illuminated.

8. The green brew size selector lights on the

LED Control Center will flash to indicate the

Brewer needs to be primed. Make sure the

handle is all the way down before continuing.

Please note, a K-Cup

should not be used

for the Priming Sequence.

9. Press the flashing Brew Button.

10.The Brewer will automatically fill with water

(priming it) and then the water will be heat-

ed. This will take less than 5 minutes.

During the heating period the red light next

to 'HEATING' on the LED Control Center will

become illuminated. Once the water is heat-

ed, the red light will turn off.

11.Raise the handle, then press the flashing

back lit blue Brew Button to start a

cleansing brew, during which hot water will

flow into your cup or mug. Pour the hot

water into the sink.

12.The Brewer will take less than 20 seconds

to refill and reheat water between brews

during which time the red light next to

'HEATING' on the LED Control Center may

be illuminated. When the water has heated,

the red light will turn off.

13. The priming process is now complete and

you are ready to brew!

Ready to Brew your First Cup

1. The green light next to the Power Button on

the LED Control Center will be illuminated

to indicate the Brewer is powered on.

2. Place a cup or mug on the Drip Tray Plate.

3. Lift the Handle and the K-Cup

Holder will

open toward you.

4. Select a K-Cup

portion pack.

5. Place a K-Cup

portion pack in the K-Cup

Holder (as shown in exhibit at top of page).

6. Lower the Handle completely to close the

Lid.

7. Select the brew size you want using the

rotary selector switch.

8. Press the flashing blue Brew Button on the

LED Control Center. This will yield a serv-

ing of the selected size; small 6 oz. medium

8 oz. and large 10 oz. nominal sizes.

9. The blue Brew Button on the LED Control

Center will be on while brewing.

10.There may be a short pause before the brew-

ing process begins. The entire brew process

lasts for approximately 40 to 50 seconds

and ends with a burst of air to remove all

liquid coffee or tea from the K-Cup

. The

blue Brew Button will go off.

11.Lift the Handle to remove and dispose of

the used K-Cup

. CAUTION: K-Cup

will

be hot.

12.Enjoy your first cup of Keurig Brewed

gourmet coffee or tea!

13. The red light next to 'HEATING' on the

LED Control Center may light as the water

is heated for the next brew cycle. The

Brewer will be ready for use in approxi-

mately 20 seconds.

Stopping the Brew Process

If you need to stop the brewing after the

process has started, press the Power Button

to turn the Brewer ‘OFF’. The flow of coffee or

tea will stop, the heating element will shut off

and the green light next to the Power Button

will extinguish.

NOTE: You may see small amounts of water

coming from the Vent and dripping into the

Water Reservoir during this and subsequent

heating – this is normal.

NOTE: Do not remove the foil lid or

puncture the K-Cup

portion pack.

NOTE: If the Water Reservoir is empty or not

in place on the Brewer, then the blue light

next to 'ADD WATER' on the LED Control

Center will be illuminated. The Brew Button

will not be activated until water is added to

the Water Reservoir.

CAUTION: There are two sharp needles that

puncture the K-Cup

portion pack, one above

the K-Cup Holder and the other in the bottom

of the K-Cup Holder. T

o avoid risk of injury,

do not put your fingers in the K-Cup Chamber

NOTE: If you do not push the flashing Brew

Button in 60 seconds, the Brew Button will

be disabled to prevent accidental activation.

Re-activate the Brew Button by raising and

lowering the Handle completely, without

removing the unused K-Cup

CAUTION: There is extremely hot water in

the K-Cup Holder during the brew process.

o avoid risk of injury, do not lift the

Handle or open the K-Cup

Chamber

during the brew process.

Handle

K-Cup

Chamber

NOTE: If Brewer has been exposed to tempera-

tures below freezing, allow Brewer at least two

hours to reach room temperature before prim-

ing. A frozen or extremely cold brewer will not

prime properly and can cause damage.

NOTE: Following the brew, your Brewer will

fill in preparation for the next brew. The pump

will make a vibrating sound. This is normal.

K-Cup

portion pack

NOTE: You may get less coffee or tea in your

cup during your next brew. We recommend

that you perform a cleansing brew without a

K-Cup

after a terminated brew or when a prime

sequence has been completed. Then your

NEXT brew will be the proper selected volume.

Keurig Office Pro B145 Seite 7

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Missbrauch melden von Frage und/oder Antwort

Art des Missbrauchs:

Forenregeln

Neu registrieren

Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Ihre Frage wurde zu diesem Forum hinzugefügt

Info