Bedienungsanleitung Kicker CX600.5 (Seite 6 von 32) (Deutsch, Englisch, Französisch, Spanisch)

508909

Zoom out

Zoom in

Vorherige Seite

1/32

Nächste Seite

OPERATION

Automatic Turn-On Selection: The CX series offers two different automatic turn-on modes; +12V and DC

Offset.

• Remote Turn-On: Run 18 gauge wire from the Remote Turn-On Lead on your source unit to the terminal

labeled REM between the ampliﬁ er’s positive and negative power terminals. This is the preferred automatic

turn-on method.

• DC Offset Turn-On: The DC Offset mode detects a 6V DC offset from the HI-Level speaker outputs when

the source unit has been turned on.

Input Level: The RCA inputs on KICKER CX ampliﬁ ers are capable of receiving either Hi or Low-level signals

from your source unit. If the only output available from your source unit is a Hi-Level signal, simply press in the

Input Level switch on the ampliﬁ er. Refer to the wiring section of this manual for additional instructions.

Fader Switch: Depress the fader switch if you are running two sets of inputs (front and rear for example) to the

ampliﬁ er. Leave the fader switch OFF if you want to drive all channels from a single stereo input.

Sub Input: If there is no dedicated output on your source unit for a subwoofer, use the SUB INPUT switch to set

your subwoofer input to either SUB INPUT or AMP INPUT 2.

Input Gain Control: The input gain control is not a volume control. It matches the output of the source unit to

the input level of the ampliﬁ er. Turn the source unit up to about 3/4 volume (if the source unit goes to 30, turn it

to 25). Next, slowly turn (clockwise) the gain on the ampliﬁ er up until you can hear audible distortion, then turn it

down a little.

Bass Boost Control: The variable bass boost control on the top of the ampliﬁ er is designed to give you

increased output, 0–12dB, at 40 Hz. The setting for this control is subjective. If you turn it up, you must readjust

the input gain control to avoid clipping the ampliﬁ er.

Crossover Control: The variable crossovers on the side panel of the ampliﬁ er allow you to adjust the crossover

frequency from 10–200Hz (AMPS 1 & 2) and 50–200Hz (SUB). The setting for this control is subjective; 80Hz is

a good place to start.

Remote Bass-CXRC (not included): With the CXRC remote bass level control, you have the ability to control

the output level of the ampliﬁ er remotely. To surface-mount the CXRC remote bass level control, simply screw the

remote to the chosen location, then run the cable from the controller to the “Remote Bass” jack on the ampliﬁ er

panel. Do NOT connect/disconnect while the ampliﬁ er is on. Connecting the 3.5mm cable without the remote

will cause the ampliﬁ er to output at full gain, possibly damaging your speakers. See page 5.

audio inputs

2012 CX 5-Channel Amp Rev F.indd 62012 CX 5-Channel Amp Rev F.indd 6 6/22/2012 3:08:51 PM6/22/2012 3:08:51 PM

Missbrauch melden von Frage und/oder Antwort

Libble nimmt den Missbrauch seiner Dienste sehr ernst. Wir setzen uns dafür ein, derartige Missbrauchsfälle gemäß den Gesetzen Ihres Heimatlandes zu behandeln. Wenn Sie eine Meldung übermitteln, überprüfen wir Ihre Informationen und ergreifen entsprechende Maßnahmen. Wir melden uns nur dann wieder bei Ihnen, wenn wir weitere Einzelheiten wissen müssen oder weitere Informationen für Sie haben.

Kicker CX600.5 Seite 6

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Missbrauch melden von Frage und/oder Antwort

Art des Missbrauchs:

Forenregeln

Neu registrieren

Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Ihre Frage wurde zu diesem Forum hinzugefügt

Info