Bedienungsanleitung Kicker IX1000.1 (Seite 6 von 28) (Deutsch, Englisch, Französisch, Spanisch)

508902

Zoom out

Zoom in

Vorherige Seite

1/28

Nächste Seite

IX AMPLIFIERS

TROUBLESHOOTING

If your ampliﬁ er does not appear to be working, check the obvious things ﬁ rst such as blown fuses, poor or

incorrect wiring connections, incorrect setting of crossover switch and gain controls, etc. There is an illuminated

blue badge on top of the ampliﬁ er denoting the power state of the amp in addition to the Protection LED on the

end panel of your KICKER IX series ampliﬁ er. When the blue badge is lit, this indicates the ampliﬁ er is turned on

and the ampliﬁ er is functioning properly.

BLUE Badge Light off, no output? With a Volt Ohm Meter (VOM) check the following:



+12 volt power

terminal (should read +12V to +16V)



Remote turn-on terminal (should read +12V to +16V)



Check for

reversed power and ground connections.



Ground terminal, for proper conductivity.



Check for blown fuses.

BLUE Badge Light on, no output? Check the following:



RCA connections



Test speaker outputs with a

“known” good speaker.



Substitute source unit with a “known” good source unit.



Check for a signal in the

RCA cable feeding the ampliﬁ er with the VOM meter set to measure “AC” voltage.

Protection LED ﬂ ashing with loud music? The red LED indicates low battery voltage. Check all the

connections in your vehicle’s charging system. It may be necessary to replace or charge your vehicle’s battery or

replace your vehicle’s alternator.

Protection LED on, no output?



Ampliﬁ er is very hot = thermal protection is engaged. Test for proper

impedance at the speaker terminals with a VOM meter (see the diagrams in this manual for minimum

recommended impedance and multiple speaker wiring suggestions). Also check for adequate airﬂ ow around

the ampliﬁ er.



Ampliﬁ er shuts down only while vehicle is running = voltage protection circuitry is engaged.

Voltage to the ampliﬁ er is not within the 10–16 volt operating range. Have the vehicle’s charging and electrical

system inspected.



Ampliﬁ er will only play at low volume levels = short circuit protection is engaged. Check

for speaker wires shorted to each other or to the vehicle chassis. Check for damaged speakers or speaker(s)

operating below the minimum recommended impedance.

No or low output?



Check the balance control on source unit



Check the RCA (or speaker input) and

speaker output connections.

Alternator noise-whining sound with engine’s RPM?



Check for damaged RCA (or speaker input) cable



Check the routing of RCA (or speaker input) cable



Check the source unit for proper grounding



Check

the gain settings and turn them down if they are set too high.

Reduced bass response? Reverse a speaker connection from positive to negative on the stereo/subwoofer

channel(s); if the bass improves, the speaker was out of phase.

Ground Noise? KICKER ampliﬁ ers are engineered to be fully compatible with all manufacturers’ head units.

Some head units may require additional grounding to prevent noise from entering the audio signal. If you are

experiencing this problem with your head unit, in most cases running a ground wire from the RCA outputs on the

head unit to the chassis will remedy this issue.

Please Note: Modern high performance speakers have a lower DC Resistance than what used to be available.

The KICKER Coaxial and Component speakers are rated at four ohms (some DC Resistances may be as low

as 3 ohms) and work with any ampliﬁ er designed to operate at a four ohm load. If you want to use two KICKER

Coaxial or Component speakers on a single channel of your ampliﬁ er, wire the speakers in series. This will

improve the sound quality, lower the total harmonic distortion and lessen the thermal load at the ampliﬁ er. This

may prevent an ampliﬁ er from shutting down due to over-current protection circuitry.

CAUTION: When jump starting the vehicle, be sure that connections made with jumper cables are correct.

Improper connections can result in blown ampliﬁ er fuses as well as the failure of other critical systems in the

vehicle.

If you have more questions about the installation or operation of your new KICKER product, see the Authorized

KICKER Dealer where you made your purchase. For more advice on installation, click on the SUPPORT tab on

the KICKER homepage, www.kicker.com. Choose the TECHNICAL SUPPORT tab, choose the subject you are

interested in, and then download or view the corresponding information. Please E-mail support@kicker.com or

call Technical Services (405) 624-8583 for unanswered or speciﬁ c questions.

2011 IX 500.1 1000.1 RevB.indd 62011 IX 500.1 1000.1 RevB.indd 6 10/12/2010 11:24:25 AM10/12/2010 11:24:25 AM

Missbrauch melden von Frage und/oder Antwort

Libble nimmt den Missbrauch seiner Dienste sehr ernst. Wir setzen uns dafür ein, derartige Missbrauchsfälle gemäß den Gesetzen Ihres Heimatlandes zu behandeln. Wenn Sie eine Meldung übermitteln, überprüfen wir Ihre Informationen und ergreifen entsprechende Maßnahmen. Wir melden uns nur dann wieder bei Ihnen, wenn wir weitere Einzelheiten wissen müssen oder weitere Informationen für Sie haben.

Kicker IX1000.1 Seite 6

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Missbrauch melden von Frage und/oder Antwort

Art des Missbrauchs:

Forenregeln

Neu registrieren

Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Ihre Frage wurde zu diesem Forum hinzugefügt

Info