Bedienungsanleitung Kicker IX500.2 (Seite 5 von 28) (Deutsch, Englisch, Französisch, Spanisch)

508903

Zoom out

Zoom in

Vorherige Seite

1/28

Nächste Seite

OPERATION

PWR PRT

GAIN

50Hz11 200Hz 0dB 18dB

X-OVER FREQ BASS BOOST

XOVER

OFF HI LO

INPUT

LEVEL

INPUT

OUTPUT

POWERSPEAKERS

GNDL+ L– R+ R– REM +12V

AUTO

TURN ON

12V DC AUDIO

OFFSET

BRIDGED

Automatic Turn-On Selection: The IX series offers three different automatic turn-on modes that can be

selected on the end panel; +12V, DC Offset, and Audio. Using either the DC Offset or Audio mode causes the

REM terminal to have +12V out for turning on additional ampliﬁ ers.

• Remote Turn-On: Set the switch to +12V to use the remote turn-on lead from your source unit. Run 18

gauge wire from the Remote Turn-On Lead on your source unit to the terminal labeled REM between the

ampliﬁ er’s positive and negative power terminals. This is the preferred automatic turn-on method.

• DC Offset Turn-On: If Remote Turn-On is not an option, the next best setting is DC Offset. The DC Offset

mode detects a 6V DC offset from the HI-Level speaker outputs when the source unit has been turned on.

• Signal Sense Turn-On: The Audio setting is the ﬁ nal alternative for Automatic turn-on. This is a Signal Sense

turn-on method that detects the incoming audio signal from your source unit and automatically turns on the

ampliﬁ er. This turn-on method will not work properly if the input gain control is not set appropriately.

Input Level: The RCA inputs on KICKER IX ampliﬁ ers are capable of receiving either Hi or Low-level signals from

your source unit. If the only output available from your source unit is a Hi-Level signal, simply press in the Input

Level switch on the ampliﬁ er. Refer to the wiring section of this manual for additional instructions.

Input Gain Control: The input gain control is not a volume control. It matches the output of the source unit to

the input level of the ampliﬁ er. Turn the source unit up to about 3/4 volume (if the source unit goes to 30, turn it

to 25). Next, slowly turn the gain on the ampliﬁ er up (clockwise) until you can hear audible distortion, then turn it

down a little.

Crossover Switch: Use the XOVER switch on the front of the ampliﬁ er to set the internal crossover to OFF, HI

or LO. When the switch is set to OFF, a full bandwidth signal will be ampliﬁ ed. Set the switch to HI if you want the

ampliﬁ er’s internal crossover to serve as a high-pass ﬁ lter. Set the switch to LO if you want the ampliﬁ er’s internal

crossover to serve as a low-pass ﬁ lter. Never change the crossover “OFF/HI/LO” switch setting with the audio

system on!

Crossover Control: The variable crossover on the front of the ampliﬁ er allows you to adjust the crossover

frequency from 50–200Hz. The setting for this control is subjective; 80Hz is a good place to start.

Bass Boost Control: The variable bass boost control on the front of the ampliﬁ er is designed to give you

increased output, 0–18dB, at 40Hz. The setting for this control is subjective. If you turn it up, you must readjust

the input gain control to avoid clipping the ampliﬁ er.

2010 IX 500.2 RevF.indd 52010 IX 500.2 RevF.indd 5 11/5/2010 12:32:11 PM11/5/2010 12:32:11 PM

Missbrauch melden von Frage und/oder Antwort

Libble nimmt den Missbrauch seiner Dienste sehr ernst. Wir setzen uns dafür ein, derartige Missbrauchsfälle gemäß den Gesetzen Ihres Heimatlandes zu behandeln. Wenn Sie eine Meldung übermitteln, überprüfen wir Ihre Informationen und ergreifen entsprechende Maßnahmen. Wir melden uns nur dann wieder bei Ihnen, wenn wir weitere Einzelheiten wissen müssen oder weitere Informationen für Sie haben.

Kicker IX500.2 Seite 5

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Missbrauch melden von Frage und/oder Antwort

Art des Missbrauchs:

Forenregeln

Neu registrieren

Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Ihre Frage wurde zu diesem Forum hinzugefügt

Info