Bedienungsanleitung Kicker KX1600.1 (Seite 6 von 28) (Deutsch, Englisch, Französisch, Spanisch)

508861

Zoom out

Zoom in

Vorherige Seite

1/28

Nächste Seite

KXRC REMOTE BASS INSTALLATION

Surface-mount the KXRC remote

using the supplied screws.

Connect the supplied cable to the KXRC remote and the

Remote Bass jack on the ampliﬁ er

back view

TROUBLESHOOTING

If your ampliﬁ er does not appear to be working, check the obvious things ﬁ rst such as blown fuses, poor or

incorrect wiring connections, incorrect setting of crossover switch and gain controls, etc. There is a Protection

(PRT) LED on the side panel of your Kicker KX series ampliﬁ er. Depending on the state of the ampliﬁ er and the

vehicle’s charging system, the LED will either glow red or be off.

Red (PRT) LED ﬂ ickering with loud music? The red (PRT) LED indicates low battery voltage. Check all the

connections in your vehicle’s charging system. It may be necessary to replace or charge your vehicle’s battery or

replace your vehicle’s alternator.

Red (PRT) LED on, no output?



Ampliﬁ er is very hot = thermal protection is engaged. Test for proper

impedance at the speaker terminals with a VOM meter (see the diagrams in this manual for minimum

recommended impedance and multiple speaker wiring suggestions). Also check for adequate airﬂ ow around

the ampliﬁ er.



Ampliﬁ er shuts down only while vehicle is running = voltage protection circuitry is engaged.

Voltage to the ampliﬁ er is not within the 10–16 volt operating range. Have the vehicle’s charging and electrical

system inspected.



Ampliﬁ er will only play at low volume levels = short circuit protection is engaged. Check

for speaker wires shorted to each other or to the vehicle chassis. Check for damaged speakers or speaker(s)

operating below the minimum recommended impedance.

No or low output?



Check the balance control on source unit



Check the RCA (or speaker input) and

speaker output connections.

Alternator noise-whining sound with engine’s RPM?



Check for damaged RCA (or speaker input) cable



Check the routing of RCA (or speaker input) cable



Check the source unit for proper grounding



Check

the gain settings and turn them down if they are set too high.

Ground Noise? KICKER ampliﬁ ers are engineered to be fully compatible with all manufacturers’ head units.

Some head units may require additional grounding to prevent noise from entering the audio signal. If you are

experiencing this problem with your head unit, in most cases running a ground wire from the RCA outputs on the

head unit to the chassis will remedy this issue.

CAUTION: When jump starting the vehicle, be sure that connections made with jumper cables are correct.

Improper connections can result in blown ampliﬁ er fuses as well as the failure of other critical systems in the

vehicle.

2013 KX Mono Amps Rev G.indd 62013 KX Mono Amps Rev G.indd 6 11/13/2012 2:17:14 PM11/13/2012 2:17:14 PM

Missbrauch melden von Frage und/oder Antwort

Libble nimmt den Missbrauch seiner Dienste sehr ernst. Wir setzen uns dafür ein, derartige Missbrauchsfälle gemäß den Gesetzen Ihres Heimatlandes zu behandeln. Wenn Sie eine Meldung übermitteln, überprüfen wir Ihre Informationen und ergreifen entsprechende Maßnahmen. Wir melden uns nur dann wieder bei Ihnen, wenn wir weitere Einzelheiten wissen müssen oder weitere Informationen für Sie haben.

Kicker KX1600.1 Seite 6

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Missbrauch melden von Frage und/oder Antwort

Art des Missbrauchs:

Forenregeln

Neu registrieren

Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Ihre Frage wurde zu diesem Forum hinzugefügt

Info