Bedienungsanleitung Kicker ZX 300.1 (Seite 5 von 28) (Deutsch, Englisch, Französisch, Spanisch)

508870

Zoom out

Zoom in

Vorherige Seite

1/28

Nächste Seite

REMOTE BASS

UTO

+12V D

AUDI

FFSET

INP

PKR

INPUT

SENSITIVIT

FF HI L

PKR

ZXRC* REMOTE BASS

INSTALLATION

1. mount the

metal bracket

* ZXRC included with ZX750.1 ONLY

4-conductor phone cable

back view

2. slide the housing until it snaps

into the metal bracket

Input Level: The RCA inputs on KICKER ZX ampliﬁ ers are capable of receiving either Hi or Low-level signals

from your source unit. If the only output available from your source unit is a Hi-Level signal, simply press in the

Input Level switch on the ampliﬁ er. Refer to the wiring section of this manual for additional instructions.

Crossover Switch (ZX300.1): Use the XOVER switch on the end panel of the ampliﬁ er to set the internal

crossover to OFF or LO. When the switch is set to OFF, a full bandwidth signal will be ampliﬁ ed. Set the switch to

LO if you want the ampliﬁ er’s internal crossover to serve as a low-pass ﬁ lter. Never change the crossover

“OFF/LO” switch setting with the audio system on!

Crossover Control (ZX400.1, ZX500.1, ZX750.1): The variable crossover on the top of the ampliﬁ er allows

you to adjust the crossover frequency from 50–200Hz. The setting for this control is subjective; 80Hz is a good

place to start.

Input Gain Control: The input gain control is not a volume control. It matches the output of the source unit to

the input level of the ampliﬁ er. Turn the source unit up to about 3/4 volume (if the source unit goes to 30, turn it

to 25). Next, slowly turn (clockwise) the gain on the ampliﬁ er up until you can hear audible distortion, then turn it

down a little.

Bass Boost Switch (ZX300.1): Turn the bass boost on to increase bass by 12db at 40 Hz. If you enable the

bass boost, it may be necessary to reduce the input gain control on the ampliﬁ er to avoid clipping.

Bass Boost Control (ZX400.1, ZX500.1, ZX750.1): The variable bass boost control on the top of the

ampliﬁ er is designed to give you increased output, 0–18dB, at 40 Hz. The setting for this control is subjective. If

you turn it up, you must readjust the input gain control to avoid clipping the ampliﬁ er.

Remote Bass-ZXRC (not included with ZX300.1, ZX400.1, ZX500.1): When the crossover on your

ampliﬁ er is set to LO pass, you have the ability to control the output level of the ampliﬁ er remotely. To mount the

ZXRC remote bass level control, simply screw the metal bracket to the chosen location, then slide the housing

onto the bracket until it snaps into place. Run the cable from the controller to the “Remote Bass” jack on the

ampliﬁ er chassis.

2011 ZX 300.1 400.1 500.1 750.1 RevC.indd 52011 ZX 300.1 400.1 500.1 750.1 RevC.indd 5 11/5/2010 1:22:36 PM11/5/2010 1:22:36 PM

Missbrauch melden von Frage und/oder Antwort

Libble nimmt den Missbrauch seiner Dienste sehr ernst. Wir setzen uns dafür ein, derartige Missbrauchsfälle gemäß den Gesetzen Ihres Heimatlandes zu behandeln. Wenn Sie eine Meldung übermitteln, überprüfen wir Ihre Informationen und ergreifen entsprechende Maßnahmen. Wir melden uns nur dann wieder bei Ihnen, wenn wir weitere Einzelheiten wissen müssen oder weitere Informationen für Sie haben.

Kicker ZX 300.1 Seite 5

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Missbrauch melden von Frage und/oder Antwort

Art des Missbrauchs:

Forenregeln

Neu registrieren

Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Ihre Frage wurde zu diesem Forum hinzugefügt

Info