Bedienungsanleitung Kicker zx 350 2 (Seite 2 von 4) (Englisch)

167673

Zoom out

Zoom in

Vorherige Seite

1/4

Nächste Seite

+12V

18"

(45cm)

24"

(60cm)

XOVER

Installation

1. Mounting Choose a structurally sound location to mount your Kicker ampliﬁ er. Make sure there

are no items behind the area where the screws will be driven. Choose a location that allows at least

4” (10cm) of open ventilation for the ampliﬁ er. If possible, mount the ampliﬁ er in the climate-controlled

passenger compartment. Drill four holes using a 7/64” (3mm) bit and use the supplied #8 screws to

mount the ampliﬁ er.

2. Wiring Disconnect the vehicle’s battery to avoid an electrical short. Then, connect the ground wire to

the ampliﬁ er. Make the ground wire short, 24” (60cm) or less, and connect it to a paint and corrosion free

solid metal area of the vehicle's chassis. Adding an additional ground wire of this same gauge (or larger)

between the battery's negative post and the vehicle chassis is recommended.

The ZX ampliﬁ er has dual input sensitivity differential RCA inputs which will receive either high or low

level signals from your car stereo’s source unit. Ideally, when connecting the source unit to the ampliﬁ er,

the ZX ampliﬁ er’s input level switch should be set to “LO” and a low-level signal should run from the

source unit’s stereo RCA output to the stereo RCA input on the end panel of the ampliﬁ er using RCA

interconnect cable. If a low-level stereo RCA output is not available on the source unit, the signal can

be delivered to the ampliﬁ er using the high-level speaker outputs on the source unit. Set the input level

switch on the end panel of the ampliﬁ er to “HI”. Crimp and solder RCA connectors to the end of the

speaker wire running from the high-level speaker outputs on the source unit and connect the wire to the

RCA Inputs on the end panel of the ampliﬁ er as shown in Figure 1. Either input method will provide a

low-level output signal at the RCA output, which effectively passes the audio signal to another ampliﬁ er

or component. Keep the audio

signal cable away from factory wiring

harnesses and other power wiring. If

you need to cross this wiring, cross it

at a 90 degree angle.

Install a fuse within 18” (45cm) of the battery and in-line with the 8 gauge power cable connected to your

ampliﬁ er. If you ever need to remove the ampliﬁ er from the vehicle after it has been installed, the ground

wire should be the last wire disconnected from the ampliﬁ er--just the opposite as when you installed it.

See the fuse chart on the following page for power and ground wire size, and fusing recommendations.

3. Conﬁ guration The following diagrams show the most common conﬁ gurations for your Kicker ZX

series ampliﬁ er.

ZX.2SeriesAmpliﬁ er

Owner’sManual

Tw o ChannelModels: ZX350.2 / ZX450.2 / ZX550.2 / ZX850.2

Authorized Kicker Dealer:

Purchase Date:

Ampliﬁ er Model Number:

Ampliﬁ er Serial Number:

Congratulations on your

KICKER purchase!

Please record your purchase

information and keep your sales

receipt for validation of warranty.

__________________________

INSTALLATION

ZX.2AMPLIFIER

CONFIGURATION

+12V

18"

(45cm)

24"

(60cm)

+12V

18"

(45cm)

24"

(60cm)

Figure 2

Figure 3

Figure 4

Minimum Impedance of 2 ohms per channel in stereo operation

Minimum impedance of 4 ohms while in bridged operation

Minimum impedance of 4 ohms mono and 2 ohms per channel in stereo simultaneously

Ground

Remote

Turn-On

Fuse

Battery

High Pass

Low Pass

Ground

Remote

Turn-On

Fuse

Battery

Ground

Remote

Turn-On

Fuse

Battery

Signal In

Bridge Wiring

Bridged Operation (Mono)

Two Channel Operation (Stereo)

Stereo and Mono Operation Simultaneously (SAMS)

Note: To get the best performance from your new Kicker Ampliﬁ er, we recommend using genuine Kicker Accessories and Wiring.

Performance

Model ZX350.2 ZX450.2 ZX550.2 ZX850.2

RMS Power in Watts, all channels driven

@14.4 Volts, 4Ω stereo, ≤ 1% THD+N

110 x 2 150 x 2 205 x 2 295 x 2

@ 2Ω stereo, ≤ 1% THD+N 175 x 2 225 x 2 275 x 2 425 x 2

@ 4Ω mono, ≤ 1% THD+N 350 450 550 850

Length: in(cm) 13 1/2 (34.2) 16 3/4 (42.5) 20 (50.7) 23 1/4 (59)

Speciﬁ cations common to all models:

Height: in(mm) 2 1/8 (54mm)

Width: in(mm) 9 5/8 (244mm)

Frequency Response, ± 0.5 db: 20 Hz - 20 kHz

Signal-to-Noise Ratio: >95db, a-weighted, re: rated power

Input Sensitivity:

Low Level: 125mV-5V

High Level: 250mV-10V

Selectable Electronic Crossover: Variable HI, LO or OFF (bypass), 50 - 200Hz, 12db/Octave

Bass Boost: Variable 0-18db Bass Boost @ 40Hz

Core Cable

Ground or Shielding

High-level Speaker Output Wire

To Ampliﬁ er

To Source Unit

Figure 1

ModelZX350.2 1 (ONE) 50 AMPERE FUSE PowerGroundWire 8GA

ModelZX450.2 1 (ONE) 60 AMPERE FUSE PowerGroundWire 4GA

ModelZX550.2 1 (ONE) 70 AMPERE FUSE PowerGroundWire 4GA

ModelZX850.2 1 (ONE) 120 AMPERE FUSE PowerGroundWire 2GA

Signal In

Signal Out

Signal In

Signal Out

Missbrauch melden von Frage und/oder Antwort

Libble nimmt den Missbrauch seiner Dienste sehr ernst. Wir setzen uns dafür ein, derartige Missbrauchsfälle gemäß den Gesetzen Ihres Heimatlandes zu behandeln. Wenn Sie eine Meldung übermitteln, überprüfen wir Ihre Informationen und ergreifen entsprechende Maßnahmen. Wir melden uns nur dann wieder bei Ihnen, wenn wir weitere Einzelheiten wissen müssen oder weitere Informationen für Sie haben.

Kicker zx 350 2 Seite 2

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Missbrauch melden von Frage und/oder Antwort

Art des Missbrauchs:

Forenregeln

Neu registrieren

Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Ihre Frage wurde zu diesem Forum hinzugefügt

Info