168211
20
Zoom out
Zoom in
Vorherige Seite
1/28
Nächste Seite
ZX AMPLIFIER
ZX300.1
ZX400.1
ZX500.1
ZX750.1
English Version
Versión Español
Amplificador del la Serie ZX.1
Deutsche Version
Stereoverstärker der ZX.1-Serie
Version Francaise
Amplificateur de série ZX.1
LIVIN’ LOUD
2011 ZX 300.1 400.1 500.1 750.1 RevC.indd 12011 ZX 300.1 400.1 500.1 750.1 RevC.indd 1 11/5/2010 1:22:27 PM11/5/2010 1:22:27 PM
2
ZX AMPLIFIERS
ZX.1-SERIES AMPLIFIERS Owner’s Manual
INSTALLATION
Mounting: Choose a structurally sound location to mount your KICKER amplifi er. Make sure there are no items
behind the area where the screws will be driven. Choose a location that allows at least 4” (10cm) of open
ventilation for the amplifi er. If possible, mount the amplifi er in the climate-controlled passenger compartment. Drill
four holes using a 7/64” (3mm) bit and use the supplied #8 screws to mount the amplifi er.
Wiring: Disconnect the vehicle’s battery to avoid an electrical short. Then, connect the ground wire to the
amplifi er. Make the ground wire short, 24” (60cm) or less, and connect it to a paint-and-corrosion-free, solid,
metal area of the vehicle’s chassis. Adding an additional ground wire of this same gauge (or larger) between the
battery’s negative post and the vehicle chassis is recommended.
The ZX amplifi er has dual input sensitivity differential RCA inputs which will receive either high or low level signals
from your car stereo’s source unit. A high-level signal can be run from the source unit’s speaker outputs to the
stereo RCA input on the end panel of the amplifi er using the KICKER ZISL as shown (make sure you set the ZX
PERFORMANCE
Authorized KICKER Dealer:
Purchase Date:
Model Number:
Serial Number:
Model: ZX300.1 ZX400.1 ZX500.1 ZX750.1
RMS Power
@ 14.4V, 4Ω mono, 1% THD+N
@ 14.4V, 2Ω mono, 1% THD+N
150W x 1
300W x 1
200W x 1
400W x 1
250W x 1
500W x 1
375W x 1
750W x 1
Length 13-1/2”
(342mm)
10-1/4”
(260mm)
12”
(305mm)
14-11/16
(373mm)
Selectable Electronic Crossover Lo-pass,
80Hz,
24dB/octave
Variable lo-pass 50–200Hz, 24dB/octave
Bass Boost +12dB, on/off,
40Hz
Variable 0–18dB @ 40Hz
Frequency Response ± 1dB 25Hz–20kHz 25Hz–200Hz
Specifi cations common to all models:
Height 2-1/8” (54mm)
Width 9-5/8” (244mm)
Signal-to-noise Ratio >95dB, A-weighted, re: rated power
Input Sensitivity Low Level: 125mV–5V
High Level: 250mV–10V
Subsonic Filter 24dB/octave, fi xed @ 25Hz
Pro Tip: To get the best performance from your new KICKER Amplifi er and extend the warranty by 1 year, use
genuine KICKER accessories and wiring.
MODEL: ZX300.1 / ZX400.1 / ZX500.1 / ZX750.1
2011 ZX 300.1 400.1 500.1 750.1 RevC.indd 22011 ZX 300.1 400.1 500.1 750.1 RevC.indd 2 11/5/2010 1:22:35 PM11/5/2010 1:22:35 PM
3
Model External Fuse Power/Ground Wire KICKER Wiring Kit
ZX300.1 1 x 60 Ampere 8 Gauge PK8, CK8, ZCK8
ZX400.1 1 x 60 Ampere 4 Gauge PK4, CK4, ZCK4
ZX500.1 1 x 80 Ampere 4 Gauge PK4, CK4, ZCK4
ZX750.1 1 x 100 Ampere 4 Gauge PK4, CK4, ZCK4
amplifi ers input level switch to “HI”). Alternatively, the signal can be delivered to the amplifi er using the low-level
RCA outputs on the source unit. Set the input level switch on the end panel of the amplifi er to “LO”. Either input
method will provide a low-level output signal at the RCA output, which effectively passes the audio signal to
another amplifi er or component. Keep the audio signal cable away from factory wiring harnesses and other
power wiring. If you need to cross this wiring, cross it at a 90 degree angle.
source unit
high-level speaker
outputs
to amplifi er
shield
+
core conductor
GND REM +12V
12V
battery
external fuse
remote turn-on
(see page 5)
bare-metal
chassis ground
18”
(45cm)
24”
(60cm)
Install a fuse within 18” (45cm) of the battery and in-line with the power cable connected to your amplifi er. If you
ever need to remove the amplifi er from the vehicle after it has been installed, the ground wire should be the last
wire disconnected from the amplifi er--just the opposite as when you installed it.
KICKER ZISL
source unit high-level
speaker outputs
OR
to amplifi er
protection LED
2011 ZX 300.1 400.1 500.1 750.1 RevC.indd 32011 ZX 300.1 400.1 500.1 750.1 RevC.indd 3 11/5/2010 1:22:35 PM11/5/2010 1:22:35 PM
4
ZX AMPLIFIERS
AUTO
TURN ON
+12V DC AUDIO
OFFSET
XOVER
OFF LO
LO
HI
REMOTE BASS
INPUT
SPKR + SPKR -
OUTPUT
INPUT
SENSITIVITY
OFF
ON
BASS
BOOST
GAIN
LLRR
+–
MONO OPERATION
minimum impedance of 2 ohms
signal in signal out
woofer
ZX300.1
OPERATION
AUTO
TURN ON
+12V DC AUDIO
OFFSET
XOVER
OFF LO
LO
HI
REMOTE BASS
INPUT
SPKR + SPKR -
OUTPUT
INPUT
SENSITIVITY
OFF
ON
BASS
BOOST
GAIN
LLRR
Automatic Turn-On Selection: The ZX series offers three different automatic turn-on modes that can be
selected on the end panel; +12V, DC Offset, and Audio. Using either the DC Offset or Audio mode causes the
REM terminal to have +12V out for turning on additional amplifi ers.
Remote Turn-On: Set the switch to +12V to use the remote turn-on lead from your source unit. Run 18
gauge wire from the Remote Turn-On Lead on your source unit to the terminal labeled REM between the
amplifi ers positive and negative power terminals. This is the preferred automatic turn-on method.
DC Offset Turn-On: If Remote Turn-On is not an option, the next best setting is DC Offset. The DC Offset
mode detects a 6V DC offset from the HI-Level speaker outputs when the source unit has been turned on.
Signal Sense Turn-On: The Audio setting is the fi nal alternative for Automatic turn-on. This is a Signal Sense
turn-on method that detects the incoming audio signal from your source unit and automatically turns on the
amp. This turn-on method will not work properly if the input gain control is not set appropriately.
2011 ZX 300.1 400.1 500.1 750.1 RevC.indd 42011 ZX 300.1 400.1 500.1 750.1 RevC.indd 4 11/5/2010 1:22:36 PM11/5/2010 1:22:36 PM
5
REMOTE BASS
A
UTO
T
U
RN
ON
+12V D
C
AUDI
O
O
FFSET
L
O
HI
INP
UT
S
PKR
+
S
PKR
-
INPUT
SENSITIVIT
Y
L
X
O
VE
R
FF HI L
OU
TP
UT
L
R
R
S
PKR
+
S
PKR
-
ZXRC* REMOTE BASS
INSTALLATION
1. mount the
metal bracket
* ZXRC included with ZX750.1 ONLY
4-conductor phone cable
back view
2. slide the housing until it snaps
into the metal bracket
Input Level: The RCA inputs on KICKER ZX amplifi ers are capable of receiving either Hi or Low-level signals
from your source unit. If the only output available from your source unit is a Hi-Level signal, simply press in the
Input Level switch on the amplifi er. Refer to the wiring section of this manual for additional instructions.
Crossover Switch (ZX300.1): Use the XOVER switch on the end panel of the amplifi er to set the internal
crossover to OFF or LO. When the switch is set to OFF, a full bandwidth signal will be amplifi ed. Set the switch to
LO if you want the amplifi ers internal crossover to serve as a low-pass fi lter. Never change the crossover
“OFF/LO” switch setting with the audio system on!
Crossover Control (ZX400.1, ZX500.1, ZX750.1): The variable crossover on the top of the amplifi er allows
you to adjust the crossover frequency from 50–200Hz. The setting for this control is subjective; 80Hz is a good
place to start.
Input Gain Control: The input gain control is not a volume control. It matches the output of the source unit to
the input level of the amplifi er. Turn the source unit up to about 3/4 volume (if the source unit goes to 30, turn it
to 25). Next, slowly turn (clockwise) the gain on the amplifi er up until you can hear audible distortion, then turn it
down a little.
Bass Boost Switch (ZX300.1): Turn the bass boost on to increase bass by 12db at 40 Hz. If you enable the
bass boost, it may be necessary to reduce the input gain control on the amplifi er to avoid clipping.
Bass Boost Control (ZX400.1, ZX500.1, ZX750.1): The variable bass boost control on the top of the
amplifi er is designed to give you increased output, 0–18dB, at 40 Hz. The setting for this control is subjective. If
you turn it up, you must readjust the input gain control to avoid clipping the amplifi er.
Remote Bass-ZXRC (not included with ZX300.1, ZX400.1, ZX500.1): When the crossover on your
amplifi er is set to LO pass, you have the ability to control the output level of the amplifi er remotely. To mount the
ZXRC remote bass level control, simply screw the metal bracket to the chosen location, then slide the housing
onto the bracket until it snaps into place. Run the cable from the controller to the “Remote Bass” jack on the
amplifi er chassis.
2011 ZX 300.1 400.1 500.1 750.1 RevC.indd 52011 ZX 300.1 400.1 500.1 750.1 RevC.indd 5 11/5/2010 1:22:36 PM11/5/2010 1:22:36 PM
6
ZX AMPLIFIERS
TROUBLESHOOTING
If your amplifi er does not appear to be working, check the obvious things fi rst such as blown fuses, poor or
incorrect wiring connections, incorrect setting of crossover switch and gain controls, etc. There is an illuminated
red badge on top of the amplifi er denoting the power state of the amp in addition to the Protection LED on the
end panel of your KICKER ZX series amplifi er. When the red badge is lit, this indicates the amplifi er is turned on
and the amplifi er is functioning properly.
RED Badge Light off, no output? With a Volt Ohm Meter (VOM) check the following:
+12 volt power
terminal (should read +12V to +16V)
Remote turn-on terminal (should read +12V to +16V)
Check for
reversed power and ground connections.
Ground terminal, for proper conductivity.
Check for blown fuses.
RED Badge Light on, no output? Check the following:
RCA connections
Test speaker outputs with a
“known” good speaker.
Substitute source unit with a “known” good source unit.
Check for a signal in the
RCA cable feeding the amplifi er with the VOM meter set to measure “AC” voltage.
Protection LED fl ashing with loud music? The red LED indicates low battery voltage. Check all the
connections in your vehicle’s charging system. It may be necessary to replace or charge your vehicle’s battery or
replace your vehicle’s alternator.
Protection LED on, no output?
Amplifi er is very hot = thermal protection is engaged. Test for proper
impedance at the speaker terminals with a VOM meter (see the diagrams in this manual for minimum
recommended impedance and multiple speaker wiring suggestions). Also check for adequate airfl ow around
the amplifi er.
Amplifi er shuts down only while vehicle is running = voltage protection circuitry is engaged.
Voltage to the amplifi er is not within the 10–16 volt operating range. Have the vehicle’s charging and electrical
system inspected.
Amplifi er will only play at low volume levels = short circuit protection is engaged. Check
for speaker wires shorted to each other or to the vehicle chassis. Check for damaged speakers or speaker(s)
operating below the minimum recommended impedance.
No or low output?
Check the balance control on source unit
Check the RCA (or speaker input) and
speaker output connections.
Alternator noise-whining sound with engine’s RPM?
Check for damaged RCA (or speaker input) cable
Check the routing of RCA (or speaker input) cable
Check the source unit for proper grounding
Check
the gain settings and turn them down if they are set too high.
Reduced bass response? Reverse a speaker connection from positive to negative on the stereo/subwoofer
channel(s); if the bass improves, the speaker was out of phase.
Ground Noise? KICKER amplifi ers are engineered to be fully compatible with all manufacturers’ head units.
Some head units may require additional grounding to prevent noise from entering the audio signal. If you are
experiencing this problem with your head unit, in most cases running a ground wire from the RCA outputs on the
head unit to the chassis will remedy this issue.
Please Note: Modern high performance speakers have a lower DC Resistance than what used to be available.
The KICKER Coaxial and Component speakers are rated at four ohms (some DC Resistances may be as low
as 3 ohms) and work with any amplifi er designed to operate at a four ohm load. If you want to use two KICKER
Coaxial or Component speakers on a single channel of your amplifi er, wire the speakers in series. This will
improve the sound quality, lower the total harmonic distortion and lessen the thermal load at the amplifi er. This
may prevent an amplifi er from shutting down due to over-current protection circuitry.
CAUTION: When jump starting the vehicle, be sure that connections made with jumper cables are correct.
Improper connections can result in blown amplifi er fuses as well as the failure of other critical systems in the
vehicle.
If you have more questions about the installation or operation of your new KICKER product, see the Authorized
KICKER Dealer where you made your purchase. For more advice on installation, click on the SUPPORT tab on
the KICKER homepage, www.kicker.com. Choose the TECHNICAL SUPPORT tab, choose the subject you are
interested in, and then download or view the corresponding information. Please E-mail support@kicker.com or
call Technical Services (405) 624-8583 for unanswered or specifi c questions.
2011 ZX 300.1 400.1 500.1 750.1 RevC.indd 62011 ZX 300.1 400.1 500.1 750.1 RevC.indd 6 11/5/2010 1:22:37 PM11/5/2010 1:22:37 PM
7
KICKER will now provide a three-
year warranty with all ZX-Series
Amplifi er purchases paired with a
qualifying KICKER Installation Kit* .
This extends the standard warranty by an additional
year. Amplifi er and Kit must be purchased from an
Authorized KICKER Dealer.
KICKER ZX amplifi er success is currently at an unheard-of rate, making the extended
warranty program even more benefi cial to you.
Using poor-quality, under-spec wiring kits will impede ZX amplifi er performance.
A superior-quality KICKER installation Kit is guaranteed to extend the life of ZX
amplifi ers.
The new extended warranty applies only to KICKER amplifi ers and accessories sold to consumers by Authorized
KICKER Dealers in the United States of America or its possessions. It also only applies to the original purchaser of
KICKER amplifi ers and accessories. One warranty extension per amplifi er is allowed regardless of the number of amplifi er
installation kits purchased. This program does not apply to “B”-stock product or factory-refurbished product.
This offer is for a limited time, so see your local Authorized KICKER Dealer soon for details.
*U.S.A. Only | EE.UU. solamente | Nur USA | Les USA Seulement
ZX300.1
225 x 1 @ 4 ohms, 14.4VDC, 1% THD, CEA-2006 (Watts)
Signal to Noise Ratio -96dB CEA-2006 (ref: 1W, A-weighted)
ZX400.1
200 x 1 @ 4 ohms, 14.4VDC, 1% THD, CEA-2006 (Watts)
Signal to Noise Ratio -77dB CEA-2006 (ref: 1W, A-weighted)
ZX500.1
250 x 1 @ 4 ohms, 14.4VDC, 1% THD, CEA-2006 (Watts)
Signal to Noise Ratio -74dB CEA-2006 (ref: 1W, A-weighted)
ZX750.1
375 x 1 @ 4 ohms, 14.4VDC, 1% THD, CEA-2006 (Watts)
Signal to Noise Ratio -68dB CEA-2006 (ref: 1W, A-weighted)
2011 ZX 300.1 400.1 500.1 750.1 RevC.indd 72011 ZX 300.1 400.1 500.1 750.1 RevC.indd 7 11/5/2010 1:22:37 PM11/5/2010 1:22:37 PM
8
AMPLIFICADOR ZX
Modelo: ZX300.1 ZX400.1 ZX500.1 ZX750.1
Potencia RMS
@ 14.4V, 4Ω monofónico, 1% THD+N
@ 14.4V, 2Ω monofónico, 1% THD+N
150W x 1
300W x 1
200W x 1
400W x 1
250W x 1
500W x 1
375W x 1
750W x 1
Largo 13-1/2”
(342mm)
10-1/4”
(260mm)
12”
(305mm)
14-11/16
(373mm)
Crossover electrónico a selección Pasabajas,
80Hz,
24dB/octava
Pasabajas variable de 50–200Hz, 24dB/octava
Refuerzo de Bajos +12dB,
40Hz
Variable 0–18dB @ 40Hz
Respuesta de frecuencias ± 1dB 25Hz–20kHz 25Hz–200Hz
Especifi caciones comunes de todos los modelos:
Altura 2-1/8” (54mm)
Ancho 9-5/8” (244mm)
Relación de señal a ruido >95dB, ponderado en A, ref: potencia nominal
Sensibilidad de entrada Bajo Nivel: 125mV–5V
Alto Nivel: 250mV–10V
Filtro Subsónico
24dB/octava @ 25Hz
AMPLIFICADOR DE LA SERIE ZX.1
Manual del propietario
INSTALACIÓN
Montaje: Escoja un lugar estructuralmente sólido para montar el amplifi cador KICKER. Asegúrese de que no
haya nada por detrás de dónde van a entrar los tornillos. Escoja un lugar en que queden por lo menos 4 plg.
(10 cm) de espacio abierto de ventilación alrededor del amplifi cador. Si es posible, monte el amplifi cador en el
compartimiento de pasajeros, con ambiente acondicionado. Haga cuatro agujeros con una broca de 7/64 de
plg. (3 mm) y monte el amplifi cador con los tornillos N° 8 que se suministran.
Cableado: Desconecte la batería del vehículo para evitar cortocircuitos. Luego, conecte un cable de conexión
a tierra al amplifi cador. El cable de conexión a tierra debe ser corto, de 24 plg. (60 cm) o menos, y debe
ir conectado a un punto sólido del chasis del vehículo en que no haya ni pintura ni corrosión. También se
recomienda instalar un cable de conexión a tierra adicional, de este mismo calibre (o de mayor calibre), entre la
terminal negativa de la batería y el chasis del auto.
RENDIMIENTO
Distribuidor autorizado de KICKER:
Fecha de compra:
Número de modelo del amplifi cador:
Número de serie del amplifi cador:
Nota: Para obtener el mejor rendimiento de sus nuevos amplifi cadores KICKER, le recomendamos que use
accesorios y cableado KICKER auténticos.
MODELOS: ZX300.1 / ZX400.1 / ZX500.1 / ZX750.1
2011 ZX 300.1 400.1 500.1 750.1 RevC.indd 82011 ZX 300.1 400.1 500.1 750.1 RevC.indd 8 11/5/2010 1:22:38 PM11/5/2010 1:22:38 PM
9
Modelo Fusible
Externo
Cable de Alimentación y
Conexión a Tierra
Kit de cableado
KICKER
ZX300.1 1 x 60A Calibre 8 PK8, CK8, ZCK8
ZX400.1 1 x 60A Calibre 4 PK4, CK4, ZCK4
ZX500.1 1 x 80A Calibre 4 PK4, CK4, ZCK4
ZX750.1 1 x 100A Calibre 4 PK4, CK4, ZCK4
El amplifi cador ZX tiene entradas RCA diferenciales de doble sensibilidad de entrada que reciben señales de
alto nivel o bajo nivel de la unidad fuente del sistema estereofónico del automóvil.La señal se puede llevar al
amplifi cador desde las salidas de altavoz de alto nivel de la unidad fuente. Fije el selector de nivel de entrada del
panel de extremo del amplifi cador en la posición de alto (HI). Engarce y suelde conectores RCA al extremo del
cable de altavoz procedente de las salidas de altavoz de alto nivel de la unidad fuente y conéctelo a las entradas
RCA del panel de extremo del amplifi cador o simplifi car la instalación mediante un ZISL KICKER como se
muestra a continuación. Como alternativa, puede conectar producción de su unidad fuente a las entradas RCA
del amplifi cador ZX RCA. Fije el selector de nivel de entrada del panel de extremo del amplifi cador en la posición
de bajo (LO). Cualquiera de los métodos de entrada permite establecer una señal de salida de bajo nivel en la
salida RCA, lo cual, en efecto, pasa la señal de audio a otro amplifi cador o componente. Mantenga el cable de
señal de audio alejado de los arneses de cableado de fábrica y otros cables de alimentación. Si es necesario
cruzar este cableado, crúcelo en un ángulo de 90°.
Cable de salida
de altavoz de
alto nivel
Hacia el amplifi cador
Hacia el
amplifi cador
Conexión a tierra o blindaje
+
cable central
GND REM +12V
12V
batería
fusible
externo
encendido a distancia
(página 11)
conexión a tierra
18”
(45cm)
24”
(60cm)
Instale un fusible a menos de 18 plg. (45 cm) de la batería y en línea con el cable de alimentación conectado al
amplifi cador. Si alguna vez necesita desmontar el amplifi cador, el cable de conexión a tierra debe ser el último
que se desconecte del amplifi cador. Exactamente lo contrario de lo que se hace cuando se instala.
KICKER ZISL
Cable de salida de
altavoz de alto nivel
O
LED de “protection”
2011 ZX 300.1 400.1 500.1 750.1 RevC.indd 92011 ZX 300.1 400.1 500.1 750.1 RevC.indd 9 11/5/2010 1:22:38 PM11/5/2010 1:22:38 PM
10
AMPLIFICADOR ZX
AUTO
TURN ON
+12V DC AUDIO
OFFSET
XOVER
OFF LO
LO
HI
REMOTE BASS
INPUT
SPKR + SPKR -
OUTPUT
INPUT
SENSITIVITY
OFF
ON
BASS
BOOST
GAIN
LLRR
+–
FUNCIONAMIENTO MONOFÓNICO
impedancia mínima de 2 ohmios
woofer
Selección de Encendido Automático: La serie ZX ofrece tres modalidades de encendido automático que se
pueden seleccionar en el panel de extremo: +12V, compensación de CC y audio. Las modalidades de audio o
compensación de CC dan +12V a la terminal REM para encender otros amplifi cadores.
Encendido a Distancia: Ponga el selector en +12V para usar el conductor de encendido a distancia de la
unidad fuente. Instale cable calibre 18 desde el conductor de encendido a distancia de la unidad fuente
hasta la terminal etiquetada REM entre las terminales de alimentación positiva y negativa del amplifi cador.
Este es el método de encendido automático preferido.
Encendido por Compensación de CC: Si el encendido a distancia no es posible, la siguiente opción
preferible es DC Offset. En la modalidad de compensación de CC, el amplifi cador detecta una subida de
6V de las salidas de altavoz de alto nivel cuando la unidad fuente se ha encendido.
Encendido por Detección de Señal: La modalidad de es la opción fi nal de encendido automático. Este es
un método de encendido en que el amplifi cador detecta la señal de audio procedente de la unidad fuente
y se enciende automáticamente. Este método de encendido no funciona correctamente si el control de
amplifi cación de entrada no se ha fi jado correctamente.
señal de salidaseñal de entrada
ZX300.1
FUNCIONAMIENTO
AUTO
TURN ON
+12V DC AUDIO
OFFSET
XOVER
OFF LO
LO
HI
REMOTE BASS
INPUT
SPKR + SPKR -
OUTPUT
INPUT
SENSITIVITY
OFF
ON
BASS
BOOST
GAIN
LLRR
2011 ZX 300.1 400.1 500.1 750.1 RevC.indd 102011 ZX 300.1 400.1 500.1 750.1 RevC.indd 10 11/5/2010 1:22:39 PM11/5/2010 1:22:39 PM
20
AMPLIFICATEUR ZX
Modèle: ZX300.1 ZX400.1 ZX500.1 ZX750.1
Puissance Effi cace
@ 14.4V, 4Ω mono, 1% THD+N
@ 14.4V, 2Ω mono, 1% THD+N
150W x 1
300W x 1
200W x 1
400W x 1
250W x 1
500W x 1
375W x 1
750W x 1
Longueur 13-1/2”
(342mm)
10-1/4”
(260mm)
12”
(305mm)
14-11/16
(373mm)
Filtre Électronique Sélectionnable Passe-bas,
80Hz,
24dB/octave
Passe-bas variable de 50–200Hz, 24dB/octave
Amplifi cation des Graves +12dB,
40Hz
Variable 0–18dB @ 40Hz
Réponse en Fréquence ± 1dB 25Hz–20kHz 25Hz–200Hz
Spécifi cations communes à tous les modèles :
Hauteur 2-1/8” (54mm)
Largeur 9-5/8” (244mm)
Rapport Signal sur Bruit >95dB, une puissance nominale
Sensibilité d’Entrée Bas niveau: 125mV–5V
Haut niveau: 250mV–10V
Filtre Subsonique 24dB/octave @ 25Hz
AMPLIFICATEUR SÉRIE ZX.1 Manuel d’utilisation
INSTALLATION
Montage: Choisissez un emplacement de structure saine pour monter votre amplifi cateur KICKER. Assurez-
vous que l’arrière de l’emplacement où vous allez enfoncer les vis ne comporte aucun élément. Choisissez un
endroit assurant au moins 10 cm (4 po) de dégagement de ventilation ouverte pour l’amplifi cateur. Si possible,
montez l’amplifi cateur dans l’habitacle passager climatisé. Percez quatre trous à l’aide d’un foret de 3 mm (7/64
po) et utilisez les vis nº 8 fournies pour monter l’amplifi cateur.
Câblage: Débranchez la batterie du véhicule pour éviter un court-circuit. Ensuite, raccordez le fi l de masse à
l’amplifi cateur. Le fi l de masse doit être le plus court possible, de 60 cm (24 po) maximum. Raccordez-le à une
partie métallique solide du châssis du véhicule, ne comportant ni peinture ni rouille. Il est recommandé d’ajouter
un fi l de masse supplémentaire de même calibre (ou de calibre supérieur) entre la borne négative de la batterie et
le châssis du véhicule.
PERFORMANCES
Revendeur agréé KICKER :
Date d’achat :
Numéro de modèle de l’amplifi cateur :
Numéro de série de l’amplifi cateur :
Remarque : Pour optimiser les performances de votre nouvel amplifi cateur KICKER, il est conseillé d’utiliser des
accessoires et des câbles KICKER d’origine.
MODÈLE: ZX300.1 / ZX400.1 / ZX500.1 / ZX750.1
2011 ZX 300.1 400.1 500.1 750.1 RevC.indd 202011 ZX 300.1 400.1 500.1 750.1 RevC.indd 20 11/5/2010 1:22:43 PM11/5/2010 1:22:43 PM
20

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Forenregeln

Missbrauch melden von Frage und/oder Antwort

Libble nimmt den Missbrauch seiner Dienste sehr ernst. Wir setzen uns dafür ein, derartige Missbrauchsfälle gemäß den Gesetzen Ihres Heimatlandes zu behandeln. Wenn Sie eine Meldung übermitteln, überprüfen wir Ihre Informationen und ergreifen entsprechende Maßnahmen. Wir melden uns nur dann wieder bei Ihnen, wenn wir weitere Einzelheiten wissen müssen oder weitere Informationen für Sie haben.

Art des Missbrauchs:

Zum Beispiel antisemitische Inhalte, rassistische Inhalte oder Material, das zu einer Gewalttat führen könnte.

Beispielsweise eine Kreditkartennummer, persönliche Identifikationsnummer oder unveröffentlichte Privatadresse. Beachten Sie, dass E-Mail-Adressen und der vollständige Name nicht als private Informationen angesehen werden.

Forenregeln

Um zu sinnvolle Fragen zu kommen halten Sie sich bitte an folgende Spielregeln:

Neu registrieren

Registrieren auf E - Mails für Kicker zx 500 1 wenn:


Sie erhalten eine E-Mail, um sich für eine oder beide Optionen anzumelden.


Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Wenn Sie innerhalb von 15 Minuten keine E-Mail mit dem Handbuch erhalten haben, kann es sein, dass Sie eine falsche E-Mail-Adresse eingegeben haben oder dass Ihr ISP eine maximale Größe eingestellt hat, um E-Mails zu erhalten, die kleiner als die Größe des Handbuchs sind.

Ihre Frage wurde zu diesem Forum hinzugefügt

Möchten Sie eine E-Mail erhalten, wenn neue Antworten und Fragen veröffentlicht werden? Geben Sie bitte Ihre Email-Adresse ein.



Info