Bedienungsanleitung Kinzo 25 c 19 (Seite 23 von 64) (Deutsch, Englisch, Holländisch, Dänisch, Französisch, Italienisch, Portugiesisch, Spanisch, Polnisch, Türkisch, Schwedisch, Norwegisch, Finnisch)

388812

Zoom out

Zoom in

Vorherige Seite

1/64

Nächste Seite

25C19 23

ENGLISH

■ Fasten the separate chuck (12) on the

screw-thread. Tighten securely but do not

force.

■ In order to remove the chuck, proceed in

reverse order.

Use the separate chuck for drilling

without hammering exclusively.

If you use the chuck in another

function it will be damaged.

For inserting a drill bit in the separate chuck

proceed as follows:

■ Open the chuck (12).

■ Insert the drill into the chuck.

■ Fasten the chuck by hand.

■ Fasten the chuck firmly by inserting the

chuck key in one of the holes in the side

of the chuck and turning it clockwise.

■ In order to remove a drill, proceed in

reverse order.

Before inserting or removing a

drill, always pull the plug from

the wall socket.

Using the dust collector (fig. B)

The dust collector is used for drilling into

ceilings.

■ Slide the dust collector (10) onto the shaft

of the bit and mount the bit as described

above in the drill chuck.

Mounting the side grip (fig. A)

■ Loosen the side grip (7).

■ Slide the holder of the side grip over the

drill chuck on the machine.

■ Turn the side grip in de required position

and tighten it firmly.

Mounting the depth stop (fig. A)

The depth stop is used to limited the

maximum drilling depth.

■ Loosen the side grip (7).

■ Insert the depth stop (6) in the hole in the

holder of the side grip.

■ Adjust the depth stop to the required

drilling depth.

■ Tighten the side grip firmly.

Selecting the operating mode (fig. A)

The machine must be set to the required

function (drilling, hammer drilling or

chiseling) before use.

■ For drilling without hammering (in soft

stone, wood or steel) you turn the hammer

function switch (2) to position

and the

chisel function switch (3) to position

■ For hammer drilling (in concrete or hard

stone) you turn the hammer function

switch (2) to position and the chisel

function switch (3) to position

■ For chiseling you turn the hammer

function switch (2) to position

and the

chisel function switch (3) to position

. In

this position the drill chuck does not rotate.

Only set the hammer functions (2)

and (3) when the machine is

switched off.

Instructions for use

■ Before inserting a drill bit or chisel,

always grease the shaft.

■ When a cold machine is to be used for

chiselling, first let it run idle for a few

minutes to allow the grease to spread in

the mechanism.

■ If the machine does not hammer properly,

first check if the switch is in the

hammering position and if the drill bit or

chisel is correctly fitted.

■ The separate chuck cannot be used for

hammer drilling!

■ Vibrations may cause slight leakage of oil

through the joints of the housing. In this

case, you need to tighten the bolts.

Switching on and off (fig. A)

■ To switch on the machine, press the on/

off switch (1).

Missbrauch melden von Frage und/oder Antwort

Libble nimmt den Missbrauch seiner Dienste sehr ernst. Wir setzen uns dafür ein, derartige Missbrauchsfälle gemäß den Gesetzen Ihres Heimatlandes zu behandeln. Wenn Sie eine Meldung übermitteln, überprüfen wir Ihre Informationen und ergreifen entsprechende Maßnahmen. Wir melden uns nur dann wieder bei Ihnen, wenn wir weitere Einzelheiten wissen müssen oder weitere Informationen für Sie haben.

Kinzo 25 c 19 Seite 23

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Missbrauch melden von Frage und/oder Antwort

Art des Missbrauchs:

Forenregeln

Neu registrieren

Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Ihre Frage wurde zu diesem Forum hinzugefügt

Info