Bedienungsanleitung Kinzo 71779 (Seite 6 von 44) (Deutsch, Englisch, Holländisch, Französisch, Polnisch)

483680

Zoom out

Zoom in

Vorherige Seite

1/44

Nächste Seite

General

Never use a blade unsuitable for the task and item to be cut.

Hold the saw in front of you with a ﬁrm grip on the handle.

Ensure that the saw blade is not touching anything and that the power cable is not in the way when starting

the saw.

Make sure that the item is clamped tight, and that the saw line is clearly marked.

Connect the vacuum extractor nozzle to an extractor system where possible.

Start the saw. Place the soleplate on the item, and let the saw blade touch the saw line.

Saw, but do not place more pressure on the blade than is necessary. Avoid lateral pressure on the blade.

Special notes on jig sawing

Place the soleplate on the item so the saw blade is vertical and correctly positioned in relation to the saw line

without touching it.

Start the saw and tilt it carefully while supporting it using the soleplate until the blade touches the item at

the saw line.

Let the blade work through the item, continuing to tip the saw downwards until the sole is ﬂush to the item

and the blade is perpendicular to it. If necessary, drill a hole of suitable diameter in the item for use as starting

point.

Sawing wood

Check that the item does not contain nails or other metal objects. Always wear a mask.

Sawing metal

We recommend lubricating the material and saw blade with cutting oil to protect the tool and avoid over-

heating. Support the item with wooden blocks on either side.

Sawing plastic

Make a test cut ﬁrst to check if the material can tolerate the heat generated by sawing.

Important!

Check all screws on the saw regularly, particularly those that hold the blade. Tighten if required.

Check regularly that the carbon brushes are in a good condition. If the carbon brushes are worn,

they should be replaced.

Lubrication (Fig. 2)

Regularly apply a drop of oil to lubricate the guide roller (7).

cleaninG and mainTenance

Wipe the saw using a well-wrung cloth after use, and always keep the surface and ventilation holes free of

dirt. Keep the soleplate free of dirt to avoid the saw cutting incorrectly.

Never use corrosive or abrasive cleaning agents, as they may attack the plastic parts of the saw.

recyclinG

Meaning of crossed –out wheeled dustbin:

Do not dispose of electrical appliances as unsorted municipal waste, use separate collection facili-

ties. Contact you local government for information regarding the collection systems available. If

electrical appliances are disposed of in landﬁlls or dumps, hazardous substances can leak into the

groundwater and get into the food chain, damaging your health and well-being.

When replacing old appliances with new ones, the retailer is legally obligated to take back your old ap-

pliance for disposals at least free of charge

71779 manual.indd 6 31-12-10 14:49

Missbrauch melden von Frage und/oder Antwort

Libble nimmt den Missbrauch seiner Dienste sehr ernst. Wir setzen uns dafür ein, derartige Missbrauchsfälle gemäß den Gesetzen Ihres Heimatlandes zu behandeln. Wenn Sie eine Meldung übermitteln, überprüfen wir Ihre Informationen und ergreifen entsprechende Maßnahmen. Wir melden uns nur dann wieder bei Ihnen, wenn wir weitere Einzelheiten wissen müssen oder weitere Informationen für Sie haben.

Kinzo 71779 Seite 6

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Missbrauch melden von Frage und/oder Antwort

Art des Missbrauchs:

Forenregeln

Neu registrieren

Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Ihre Frage wurde zu diesem Forum hinzugefügt

Info