Bedienungsanleitung Kinzo 72122 (Seite 7 von 52) (Deutsch, Englisch, Holländisch, Französisch, Polnisch)

483682

Zoom out

Zoom in

Vorherige Seite

1/52

Nächste Seite

3-1. Switch lock

The switch trigger can be locked in the center position. (See Fig. 5)

This helps to reduce the possibility of accidental starting when not in use.

To lock the switch trigger, place the Direction of rotation selector in the center position.

3-2. Direction of rotation is controlled by the direction of rotation selector (3)

located above the switch trigger.

To select forward rotation, release the on/oﬀ switch and push the forward/reverse lever to Left side of the

tool. To select reverse rotation, push the lever to right side of the tool. When the selector is in center position,

the switch trigger is locked. (See Fig. 5)

3-3. Variable speed

This tool has a variable speed switch that delivers higher speed and torque with increased trigger pressure.

Speed is controlled by the amount of switch trigger depression.

4. Installing and Removing a Bit and a Drill (Fig. 6)

1. Hold ring A of the drill chuck tight with one hand.

2. Turn upper ring B anticlockwise with the other hand until

the drill chuck opening is large enough to accept the tool.

3. Insert the drill or the screwdriver bit into the drill chuck.

4. Turn ring B clockwise until the tool is clamped tightly.

Remove the tool in the opposite way.

5. Adjusting the torque

The torque is adjusted by rotating the torque setting (2),

the torque is greater when the torque setting is set on a higher posi-

tion. The torque is less when the torque setting is set on a low position

“1”denote lowest and “ ” denote highest.Torque is set by means of a torque setting according to diﬀ erent

screw and diﬀ erent material, you can adjust suitable torque, if the screw is long and material is hard,

you can adjust the bigger setting.

6. Drilling

Before use for drilling, the torque setting should be set on drill position “ ”.

When drilling hard smooth surface, use a center punch to mark the desired hole location. This will prevent

the drill bit from slipping oﬀ center as the hole is started. Hold the tool ﬁ rmly and place the tip of the drill

or bit into the work piece, applying only enough pressure to keep the bit cutting. Do not force or apply side

pressure to elongate a hole.

7. Wood Drilling

For maximum performance, use high speed steel drills for wood drilling, turn the torque setting on the drill

position“ ”. Begin drilling at a very low speed to prevent the bit from slipping oﬀ the starting point. Increase

the speed as the drill bit bites into the material. When drilling through holes, place a block or wood behind

the work piece to prevent ragged or edges on the back side of the hole.

8. Metal drilling

For maximum performance, use high steel bits for metal or steel drilling. Turn the torque setting on the drill

position“ ”. Begin drilling at a very low speed to prevent the bit from slipping oﬀ the starting point. Maintain

a speed and pressure which allows cutting without overheating the bit. Applying too much pressure will

overheat the drill, wear the bearings, bend or burn bits, produce oﬀ -center or irregular shaped holes.

When drilling large holes in metal, it is recommended that you drill with a small bit at ﬁ rst, then ﬁ nish with a

large bit, also lubricate the bit with oil to improve drilling action and increase bit life.

9. Disposal of an exhausted battery

To preserve natural resources place recycle or dispose of the battery properly.

This product contains Ni-Cd batteries. Consult your local waste authority for information regarding available

recycling and /or disposal options.

Fig. 6

72122 Manual.indd 7 31-12-10 15:36

Missbrauch melden von Frage und/oder Antwort

Libble nimmt den Missbrauch seiner Dienste sehr ernst. Wir setzen uns dafür ein, derartige Missbrauchsfälle gemäß den Gesetzen Ihres Heimatlandes zu behandeln. Wenn Sie eine Meldung übermitteln, überprüfen wir Ihre Informationen und ergreifen entsprechende Maßnahmen. Wir melden uns nur dann wieder bei Ihnen, wenn wir weitere Einzelheiten wissen müssen oder weitere Informationen für Sie haben.

Kinzo 72122 Seite 7

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Missbrauch melden von Frage und/oder Antwort

Art des Missbrauchs:

Forenregeln

Neu registrieren

Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Ihre Frage wurde zu diesem Forum hinzugefügt

Info