Bedienungsanleitung KitchenAid 720-0733 (Seite 24 von 112) (Englisch, Französisch, Spanisch)

581376

Zoom out

Zoom in

Vorherige Seite

1/112

Nächste Seite

Check and Adjust the Burners

The burners are tested and factory-set for most efficient

operation. However, variations in gas supply and other conditions

may make minor adjustments to air shutter or low flame setting

necessary.

It is recommended that a qualified person make burn

adjustments.

NOTE: The rotisserie burner cannot be adjusted.

Checking and adjusting the grill burner flames requires removing

the grates and flame tamers.

Burner Flame Characteristics

The flames of the grill burners and side burners (on some models)

should be blue and stable with no excessive noise or lifting (LP

gas flames will have a slightly yellow tip). A yellow flame indicates

not enough air. If flame is noisy or lifts away from the burner, there

is too much air. Some yellow tips on flames when the burner is

set to HIGH setting are acceptable as long as no carbon or soot

deposits appear. The flames should be approximately 1" (2.5 cm)

high

Check

that burners are not blocked by dirt, debris, insect nests,

etc

., and clean burners as necessary. If they are clean, adjust air

shutters as needed.

IMPORTANT: B

efo

re adjusting air shutters, let burners cool

completely.

To Adjust:

1. Light grill using information in the “Outdoor Grill Use” section.

2. Observe flame to determine which burners need adjustment

and how

the flame is acting.

3. Turn off the valve and wait until grill and burners cool

completely.

4. R

emove grill grates and flame tamers.

5. Remove the 1 screw and cotter clip that hold the burner in

the plac

e. Remove gas burner from the grill.

6. If flame is

yellow (not

enough air), turn air shutter adjustment

screw counterclockwise.

If flame is noisy or lifts away from burner (too much air), turn

air shutter

adjustment scr

ew clockwise.

Adjustment should be made cl

ockwise or

counterclockwise

from ¹⁄₈" (3.2 mm) to ¹⁄₄" (6.4 mm).

7. Replace gas burner, flame tamers and grates.

8. Light grill using information in the “Outdoor Grill Use” section.

See “B

urner Flame Characteristics.”

Low Flame Adjustment

If flame goes out on the “LOW” setting, the low flame setting

must be adjusted.

1. Turn off the valve and wait until grill and burners are cool.

2. Remove grill grates and flame tamers.

3. Light grill using information in the “Outdoor Grill Use” section.

4. Turn burner to its lowest setting.

5. Remove each control knob for the

main burn

er and side

burner.

6. Hold valve stem with pliers and insert a small flat-blade

screwdriver into

the shaft.

7. Watch the flame and slowly turn the screwdriver

counterclockwise.

8. Adjust flame to minimum stable flam

9. Replace the control knob and turn off the burner.

10. Repeat

steps 3 through 9 for each burner if needed.

11. Repla

ce the flame tamers and grates after the burners have

cooled.

A.Cotter clip

1" (2.5 cm)

A. Air shutter adjustment screw

A. Valve stem

B. Small flat-blade screwdriver

C. Pliers

Missbrauch melden von Frage und/oder Antwort

Libble nimmt den Missbrauch seiner Dienste sehr ernst. Wir setzen uns dafür ein, derartige Missbrauchsfälle gemäß den Gesetzen Ihres Heimatlandes zu behandeln. Wenn Sie eine Meldung übermitteln, überprüfen wir Ihre Informationen und ergreifen entsprechende Maßnahmen. Wir melden uns nur dann wieder bei Ihnen, wenn wir weitere Einzelheiten wissen müssen oder weitere Informationen für Sie haben.

KitchenAid 720-0733 Seite 24

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Missbrauch melden von Frage und/oder Antwort

Art des Missbrauchs:

Forenregeln

Neu registrieren

Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Ihre Frage wurde zu diesem Forum hinzugefügt

Info