Bedienungsanleitung KitchenAid 720-0819A (Seite 21 von 31) (Englisch, Französisch, Spanisch)

581365

Zoom out

Zoom in

Vorherige Seite

1/31

Nächste Seite

3. Check that burner operates at the new high flame setting. It

may be necessary to adjust the screw setting slightly more to get

the ideal burner flame height.

Check and Adjust the Burners

The burners are tested

and factory-set for most efficient

operation. However, variations in gas supply and other conditions

may make minor adjustments to air shutter or low flame setting

necessary. It is recommended that a qualified person make burner

adjustments.

Checking and adjusting the grill burner flames requires removing

the grates and flame tamers.

Burner Flame Characteristics

The flames of the grill burners and side burners (on some models)

should be blue and stable with no excessive noise or lifting (LP

gas flames will have a slightly yellow tip). A yellow flame indicates

not enough air. If flame is noisy or lifts away from the burner, there

is too much air. Some yellow tips on flames when the burner is set

to HIGH setting are acceptable as long as no carbon or soot

deposits appear. The flames should be approximately 1" (2.5 cm)

high.

Check that burners are not blocked by dirt, debris, insect nests,

etc., and clean as necessary. If they are clean, adjust air shutters

as needed.

IMPORTANT: Before adjusting air shutters, let burners cold

completely. To Adjust:

1. Light grill using information in the “Outdoor Grill Use” section.

2. Observe flame to determine which burners need adjustment

and how the flame is acting.

3. Turn off the valve and wait until grill and burners cold

completely.

4. Remove grill grates and flame tamers.

5. Remove the 1 scr

ew and cotter pin that hold the burner in

place. Remove gas burner from the grill.

A. Cotter pin

6. If flame is yellow (not enough air), turn air shutter adjustment

screw counterclockwise.

If flame is noisy or lifts away from burner (too much air), turn air

shutter adjustment screw clockwise.

Adjustment should be made clockwise or counter- clockwise

from 1/8” (3.2 mm) to ¼” (6.4 mm).

7. Replace gas burner, sear plates and grates.

8. Light grill using information in the “Outdoor Grill Use” section.

See “Burner Flame Characteristics.

A. Air shutter adjustment screw

Low Flame Adjustment

If flame goes out on

the “LOW” setting, the low flame setting

must be adjusted.

1. Turn off the valve and wait until grill and burners are cold.

2. Remove grill grates and flame tamers.

3. Light grill using information in the “Outdoor Grill Use” section.

4. Turn burner to its lowest setting.

5. Remove each control knob for the main burners and side

burner by loosening the setscrew with the hex key.

6. Hold valve stem with pliers and insert a small flat-blade

screwdriver into the shaft.

7. Watch the flame and slowly turn the screwdriver

counterclockwise.

8. Adjust flame to minimum stable flame.

A. Valve stem

B. Small flat-blade screwdriver

C. Pliers

9. Replace the control knob and turn off the burner.

10. Repeat steps 3 through 9 for each burner if needed.

11. Replace the flame tamers and grates after the burners have

been cold.

Missbrauch melden von Frage und/oder Antwort

Libble nimmt den Missbrauch seiner Dienste sehr ernst. Wir setzen uns dafür ein, derartige Missbrauchsfälle gemäß den Gesetzen Ihres Heimatlandes zu behandeln. Wenn Sie eine Meldung übermitteln, überprüfen wir Ihre Informationen und ergreifen entsprechende Maßnahmen. Wir melden uns nur dann wieder bei Ihnen, wenn wir weitere Einzelheiten wissen müssen oder weitere Informationen für Sie haben.

KitchenAid 720-0819A Seite 21

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Missbrauch melden von Frage und/oder Antwort

Art des Missbrauchs:

Forenregeln

Neu registrieren

Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Ihre Frage wurde zu diesem Forum hinzugefügt

Info