Bedienungsanleitung KitchenAid 730-0787D (Seite 23 von 97) (Englisch, Französisch, Spanisch)

581368

Zoom out

Zoom in

Vorherige Seite

1/97

Nächste Seite

Check and Adjust the Burners

The burners are tested and factory-set for most efficient

operation. However, variations in gas supply and other

conditions may make minor adjustments to air shutter or low

flame setting necessary. It is recommended that a qualified

person make burner adjustments.

Checking and adjusting the grill burner flames requires removing

6. If flame is yellow (not enough air), turn air shutter

adjustment screw counterclockwise.

Note: If flame is noisy or lifts away from burner (too much air),

turn air shutter adjustment screw clockwise.

Adjustment should be made clockwise or counter clockwise

from 1/8” (3.2 mm) to ¼” (6.4 mm).

Rl b lt d t

Checking

and

adjusting

the

grill

burner

flames

requires

removing

the grates and flame tamers.

ace gas

urner, sear p

es an

gra

es.

8. Light grill using information in the “Outdoor Grill Use”

section. See “Burner Flame Characteristics

The flames of the grill burners and side burners (on some

models) should be blue and stable with no excessive noise or

lifting (LP gas flames will have a slightly yellow tip). A yellow

flame indicates not enough air. If flame is noisy or lifts away

from the burner there is too much air Some yellow tips on

Burner Flame Characteristics

A. Air shutter adjustment screw

If flame goes out on the “LOW” setting, the low flame setting

must be adjusted.

1. Turn off the valve and wait until grill and burners are cool.

2. Remove

rill

rates and flame tamers.

from

the

burner

there

too

much

air

Some

yellow

tips

flames when the burner is set to HIGH setting are acceptable as

long as no carbon or soot deposits appear. The flames should

be approximately 1" (2.5 cm) high.

Low Flame Adjustment

3. Light grill using information in the “Outdoor Grill Use”

section.

4. Turn burner to its lowest setting.

5. Remove each control knob for the main burners and side

burner by pulling the control knob away from the grill.

6. Hold valve stem with

liers and insert a small 6” flat-

Check that burners are not blocked by dirt, debris, insect

nests, etc., and clean as necessary. If they are clean, adjust

air shutters as needed.

IMPORTANT:

Before adjusting air shutters, let burners cool

blade screwdriver into the shaft.

7. Watch the flame and slowly turn the screwdriver

counterclockwise.

8. Adjust flame to minimum stable flame.

IMPORTANT:

Before

adjusting

air

shutters,

let

burners

cool

down completely. To Adjust:

1. Light grill using information in the “Outdoor Grill Use”

section.

2. Observe flames to determine which burners need

adjustment and how the flames are acting.

3. Turn off the valve and wait until grill and burners cool

completely

A. Valve stem

completely

4. Remove grill grates and flame tamers.

5. Remove the 1 screw and cotter pin that hold the burner

in place. Remove gas burner from the grill.

B. Smal

6” flat-blade

crewdrive

C. Pliers

9. Replace the control knob and turn off the burner.

10. Repeat steps 3 through 9 for each burner if needed.

11. Replace the flame tamers and grates after the burners

are cool.

A. Cotter pin

Missbrauch melden von Frage und/oder Antwort

Libble nimmt den Missbrauch seiner Dienste sehr ernst. Wir setzen uns dafür ein, derartige Missbrauchsfälle gemäß den Gesetzen Ihres Heimatlandes zu behandeln. Wenn Sie eine Meldung übermitteln, überprüfen wir Ihre Informationen und ergreifen entsprechende Maßnahmen. Wir melden uns nur dann wieder bei Ihnen, wenn wir weitere Einzelheiten wissen müssen oder weitere Informationen für Sie haben.

KitchenAid 730-0787D Seite 23

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Missbrauch melden von Frage und/oder Antwort

Art des Missbrauchs:

Forenregeln

Neu registrieren

Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Ihre Frage wurde zu diesem Forum hinzugefügt

Info