Bedienungsanleitung KitchenAid 740-0781 (Seite 18 von 31) (Englisch, Französisch, Spanisch)

581394

Zoom out

Zoom in

Vorherige Seite

1/31

Nächste Seite

3. Remove the infrared searing main bu

rner from firebox.

4. Use a 6 mm socket and wrench or 6 mm nut driver to remove the LP

gas orifice on the end of valve. Replace with Natural gas orifice.

5. Rei

nstall infrared searing main burner. Make sure that the igniter is

out of the way to allow proper positioning of burner. Use a Phillips

screwdriver to attach the mounting screws.

6. Use a Phillips screwdriver to reattach the igniter and infrared searing

main burner plate.

7. Rei

nstall infrared searing main burner cover. Use a Phillips

screwdriver to attach mounting screws.

8. Open the manual shutoff valve in the gas supply line. The valve is

open when the handle is parallel to the gas pipe.

9. T

est all connections by brushing on an approved noncorrosive leak-

detection solution. Bubbles will show a leak. Correct any leak

found.

10. The igniter battery is not factory installed. A “AA” size alkaline

battery is located in the accessory box on the grill grate. Install

battery at this time following the instructions in “Replacing the

Igniter Battery” section.

11. Go to “Check and Adjust the Burners” section.

Record Conversion

The model/serial number plate is located on the right-hand side of the

grill. With a permanent marker, check the box next to “Natural gas” and

mark through “LP.”

In the last page of the Use and Care Guide, write “Conver

ted to Natural

Gas.” Also record the conversion date and the technician/company that

performed the conversion.

NOTE:

Place the LP gas parts in plastic parts bag for future use and

keep with package containing the literature.

Check and Adjust the Burners

The burners are tested and factory-set for most ef

ficient operation.

However, variations in gas supply and other conditions may make minor

adjustments to air shutter or low flame setting necessary.

It is recommended that a qualified person make burner adjustments.

NOTE: The rotisserie burner cannot be adjusted.

Checking and adjusting the grill burner flames requires removing the

grates and flame tamers.

Burner Flame Characteristics

The flames of the grill burners and side burners (on some models) should

be blue and stable with no excessive noise or lifting (LP gas flames will

have a slightly yellow tip). A yellow flame indicates not enough air. If

flame is noisy or lifts away from the burner, there is too much air. Some

yellow tips on flames when the burner is set to HI setting are acceptable

as long as no carbon or soot deposits appear.

Check that burners are not blocked by dirt

, debris, insect nests, etc., and

clean as necessary. If they are clean, adjust air shutters as needed.

IMPORTANT: Before adjusting

air shutters, let burners cool

completely.

To Adjust:

1. Light grill using information in the “Outdoor Grill Use” section.

2. Observe flame to determine which burners need adjustment and how

the flame is acting.

3. T

urn off the valve and wait until grill and burners cool completely.

4. Remove grill grates and flame tamers.

A. Closed valve

B. Ope

n valve

Missbrauch melden von Frage und/oder Antwort

Libble nimmt den Missbrauch seiner Dienste sehr ernst. Wir setzen uns dafür ein, derartige Missbrauchsfälle gemäß den Gesetzen Ihres Heimatlandes zu behandeln. Wenn Sie eine Meldung übermitteln, überprüfen wir Ihre Informationen und ergreifen entsprechende Maßnahmen. Wir melden uns nur dann wieder bei Ihnen, wenn wir weitere Einzelheiten wissen müssen oder weitere Informationen für Sie haben.

KitchenAid 740-0781 Seite 18

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Missbrauch melden von Frage und/oder Antwort

Art des Missbrauchs:

Forenregeln

Neu registrieren

Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Ihre Frage wurde zu diesem Forum hinzugefügt

Info