Bedienungsanleitung KitchenAid 750-0780 (Seite 18 von 29) (Englisch, Französisch, Spanisch)

581390

Zoom out

Zoom in

Vorherige Seite

1/29

Nächste Seite

Check and Adjust the Burners

The burners are

tested and factory-set for most efficient operation.

However, variations in gas supply and other conditions may make minor

adjustments to air shutter or low flame setting necessary.

It is recommended that a qualified person make burner adjustments.

NOTE: The rotisserie burner cannot be adjusted.

Checking and adjusting the grill burner flames requires removing the

grates and fl

ame tamers.

Burner Flame Characteristics

The flames of the grill burners and side burners (on some models) should

be blue

and stable with no excessive noise or lifting (LP gas flames will

have a slightly yellow tip). A yellow flame indicates not enough air. If

flame is noisy or lifts away from the burner, there is too much air. Some

yellow tips on flames when the burner is set to HI setting are acceptable

as long as no carbon or soot deposits appear. The flames should be

approximately 1" (2.5

cm) high.

1" (2.5 cm)

Check that burners are not blocked by dirt

, debris, insect nests, etc., and

clean as necessary. If they are clean, adjust air shutters as needed.

IMPORTANT: Before adjusting air shutters, let burners cool

completely.

To Adjust:

1. Light

grill using information in the “Outdoor Grill Use” section.

2. Observe flame to determine which burners need adjustment and how

the flame is acting.

3. Turn off the valve and wait until grill and burners cool completely.

4. Remove grill grates and flame tamers.

5. Remove the screw and clip that hold the burner in place. Remove

gas burner from the grill.

6. If flame is yellow (not enough air), turn air shutter adjustment screw

counterclock

wise.

If flame is noisy or lifts away from burner (too much

air), turn air

shutter adjustment screw clockwise.

A. Air shutter adjustment s

crew

Adjustment should be made clockwise or counterclockwise from 1/

8" (3.2 mm) to 1/4" (6.4 mm).

7. Replace gas

burner, flame tamers and grates.

8. Light grill using information in the “Outdoor Grill Use” section. See

“Burner Flame Characteristics.”

Low Flame Adjustment

If flame goes out on the “LO” setting,

the low flame setting must be

adjusted.

1. T

urn off the valve and wait until grill and burners are cool.

2. Remove grill grates and flame tamers.

3. Light grill using information in the “Outdoor Grill Use” section.

4. Turn burner to its lowest setting and remove knob.

5. Hold valve stem with pliers and ins

ert a small flat-blade screwdriver

into the shaft.

6. W

atch the flame and slowly turn the screwdriver counterclockwise.

Adjust flame to minimum stable flame.

A. Valve stem

B. Sma

ll flat-blade screwdriver

C. Pliers

8. Replace the control knob and turn off the burner

9. Repeat steps 3 through 8 for each burner if needed.

10. Replace the flame tamers and grates

after the burners have cooled.

A. Clip

Missbrauch melden von Frage und/oder Antwort

Libble nimmt den Missbrauch seiner Dienste sehr ernst. Wir setzen uns dafür ein, derartige Missbrauchsfälle gemäß den Gesetzen Ihres Heimatlandes zu behandeln. Wenn Sie eine Meldung übermitteln, überprüfen wir Ihre Informationen und ergreifen entsprechende Maßnahmen. Wir melden uns nur dann wieder bei Ihnen, wenn wir weitere Einzelheiten wissen müssen oder weitere Informationen für Sie haben.

KitchenAid 750-0780 Seite 18

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Missbrauch melden von Frage und/oder Antwort

Art des Missbrauchs:

Forenregeln

Neu registrieren

Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Ihre Frage wurde zu diesem Forum hinzugefügt

Info