Bedienungsanleitung KKT Kolbe CC9001IND (Seite 89 von 92) (Deutsch, Englisch)

784262

Zoom out

Zoom in

Vorherige Seite

1/92

Nächste Seite

Before connecting, check if the voltage indicated on the type plate corresponds to the mains voltage. The length of the

connection cable must be sized so that the device can be connected prior to insertion. The protective conductor must be

sized so that it is loaded onto train at the strain relief fails aer the live wires of the connection cable.

Electrical connection

•

This appliance must be earthed by law. Before connecting the appliance to the

electrical supply, check that the earth system in your house is working correctly.

•

Check that unit voltage and power, marked on the rating plate applied on the

appliance, are correct for the supply. It is necessary that the feeding network is

protected by a powerful switch able to disconnect completely the network with a

contacts separation of at least 3 mm. Be sure that the earth wire green/yellow is

not interrupted by the switch.

WARNING: THIS APPLIANCE MUST BE EARTHED

•

In order to avoid hazard, any electrical work performed on this equipment or its

associated wiring should only be done by persons authorised by the

manufacture or similary qualified persons.

Replacement or mounting of the power cord

The mains cable is replaced via the rear backboard.

The mains cable must be of the following type:

380

H05

H07

415V 3N~

RR-F

V-F 5×

RN-F

.5mm2

220-240V

H05RR-F

H05VV-F

H05RN-F

H07RN-F

3×4mm2

This appliance must be earthed by law. Before connecting

the appliance to the electrical supply, check that the earth

system in your house is working correctly.

• Check that unit voltage and power, marked on the rating

plate applied on the appliance, are correct for the supply. It

is necessary that the feeding network is protected by a pow-

erful switch able to disconnect completely the network with

a contacts separation of at least 3 mm. Be sure that the earth

wire green/yellow is not interrupted by the switch.

WARNING: THIS APPLIANCE MUST BE EARTHED

•

In order to avoid hazard, any electrical work performed on

this equipment or its associated wiring should only be done

by persons authorised by the manufacture or similary quali-

ed persons.

Replacement or mounting of the power cord

The mains cable is replaced via the rear backboard.

The mains cable must be of the following type:

Leave the mains cable slightly overlong so that you can pull out the appliance for cleaning purposes.

Proceed as follows:

• Remove the rear backboard.

• Undo the screw on the terminal block that xes the cable in place.

• Loosen the screw contacts and replace the cable with a new one of the same length.

The cable must comply with the stipulated speci- cations.

• Connect the yellow-green wire to the

terminal. This wire must be at least 10 mm

longer than the other wires.

• Connect the blue neutral wire to

terminal N.

• Connect the brown power wire to

terminal L.

Installation and connection of the appliance

Power connection

Missbrauch melden von Frage und/oder Antwort

Libble nimmt den Missbrauch seiner Dienste sehr ernst. Wir setzen uns dafür ein, derartige Missbrauchsfälle gemäß den Gesetzen Ihres Heimatlandes zu behandeln. Wenn Sie eine Meldung übermitteln, überprüfen wir Ihre Informationen und ergreifen entsprechende Maßnahmen. Wir melden uns nur dann wieder bei Ihnen, wenn wir weitere Einzelheiten wissen müssen oder weitere Informationen für Sie haben.

KKT Kolbe CC9001IND Seite 89

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Missbrauch melden von Frage und/oder Antwort

Art des Missbrauchs:

Forenregeln

Neu registrieren

Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Ihre Frage wurde zu diesem Forum hinzugefügt

Info