Bedienungsanleitung KKT Kolbe INTEGRA606 (Seite 60 von 64) (Deutsch, Englisch)

784443

Zoom out

Zoom in

Vorherige Seite

1/64

Nächste Seite

Mounting the hood

Note: When installing backow aps or a backow valve, make sure that they can open

freely. Otherwise, the suction power may be reduced and the operating noise of the

cooker bonnet increased.

Note: If the extractor hood is used for for recirculating air without venting to the outside,

it is important that the air outlet is not blocked, as otherwise the extractor hood will be

damaged, the capacity can be reduced and the operating noise will increase. It should

also be noted that a non-return valve cannot be installed.

The range hood must be pushed up until the mountings ”click”�over the construction the

range hood is to be mounted in.

If the mountings does not ”click”�they can be pushed in place, b y pressing on the screws

that holds the mountings.�This is done by pushing through the four holes in the corners of

the range hood with a screwdriver.

Note:�when mounting in a horizontal division recommends that the range hood

is insulated to avoid noise nuisance.

Click!

Ceiling

Range hood

Mounting

Adjust the mountings until the edge of the

range hood is level to the ceiling.�This is

done using a Philips screwdriver through the

four holes in the corners of the range hood.

NOTE:�After the adjustment the enclosed

plugs must be mounted in the screw

holes.�Otherwise noise nuisance can be

experienced.

The vent pipe must be mounted after the adjustment of the range hood.�Thermex

recommends that a back valve is mounted on the vent installation to prevent draft

through the vent.�When installing an external motor from Thermex the none-return valve

is placed by the motor.

The range hood must be pushed up until the mountings ”click”�over the construction the

range hood is to be mounted in.

If the mountings does not ”click”�they can be pushed in place, b y pressing on the screws

that holds the mountings.�This is done by pushing through the four holes in the corners of

the range hood with a screwdriver.

Note:�when mounting in a horizontal division recommends that the range hood

is insulated to avoid noise nuisance.

Click!

Ceiling

Range hood

Mounting

Adjust the mountings until the edge of the

range hood is level to the ceiling.�This is

done using a Philips screwdriver through the

four holes in the corners of the range hood.

NOTE:�After the adjustment the enclosed

plugs must be mounted in the screw

holes.�Otherwise noise nuisance can be

experienced.

The vent pipe must be mounted after the adjustment of the range hood.�Thermex

recommends that a back valve is mounted on the vent installation to prevent draft

through the vent.�When installing an external motor from Thermex the none-return valve

is placed by the motor.

The range hood must be pushed up until the mountings ”click”�over the construction the

range hood is to be mounted in.

If the mountings does not ”click”�they can be pushed in place, b y pressing on the screws

that holds the mountings.�This is done by pushing through the four holes in the corners of

the range hood with a screwdriver.

Note:�when mounting in a horizontal division recommends that the range hood

is insulated to avoid noise nuisance.

Click!

Ceiling

Range hood

Mounting

Adjust the mountings until the edge of the

range hood is level to the ceiling.�This is

done using a Philips screwdriver through the

four holes in the corners of the range hood.

NOTE:�After the adjustment the enclosed

plugs must be mounted in the screw

holes.�Otherwise noise nuisance can be

experienced.

The vent pipe must be mounted after the adjustment of the range hood.�Thermex

recommends that a back valve is mounted on the vent installation to prevent draft

through the vent.�When installing an external motor from Thermex the none-return valve

is placed by the motor.

The cooker hood must be pushed upwards until the brackets „click“ over the construction

in which the cooker hood is to be mounted.

If the brackets do not „click“, they can be brought into position by pressing the screws

holding the brackets. To do this, insert a screwdriver through the four holes in the corners

of the cooker hood, put it into the holes and press the holding screws.

Note: For horizontal installation, it is advisable to insulate the cooker hood to prevent the

formation of annoying noises.

ceiling

hood body

bracket

Note: Aer adjustment, the enclosed

plugs must be mounted in the screw

holes.

Otherwise, annoying noises may occur.

Adjust the brackets so that the edge of

the cooker hood is level to the ceiling.

This is done by inserting a screwdriver

trough the four holes in the corner of the

range hood as described before.

Missbrauch melden von Frage und/oder Antwort

Libble nimmt den Missbrauch seiner Dienste sehr ernst. Wir setzen uns dafür ein, derartige Missbrauchsfälle gemäß den Gesetzen Ihres Heimatlandes zu behandeln. Wenn Sie eine Meldung übermitteln, überprüfen wir Ihre Informationen und ergreifen entsprechende Maßnahmen. Wir melden uns nur dann wieder bei Ihnen, wenn wir weitere Einzelheiten wissen müssen oder weitere Informationen für Sie haben.

KKT Kolbe INTEGRA606 Seite 60

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Missbrauch melden von Frage und/oder Antwort

Art des Missbrauchs:

Forenregeln

Neu registrieren

Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Ihre Frage wurde zu diesem Forum hinzugefügt

Info