Bedienungsanleitung Klarstein 10030984 (Seite 6 von 16) (Deutsch, Englisch, Französisch, Italienisch, Spanisch)

778319

Zoom out

Zoom in

Vorherige Seite

1/16

Nächste Seite

Special Safety Notes

• As there is the risk of burns, always close the lid and lock it properly when you are going to turn the kettle on.

Never open the lid while hot water is inside and /or the steam density is too high.

• Before switching on the kettle ensure that the water level is between 0.5 and 1.8 liter marks only.

• There is a cut-off device that works if the kettle is overheated. It switches the kettle off when there is no

water inside or the water level is too low. Wait until the kettle cools down completely to start boiling after the

cut-off device was activated. The kettle will not turn on while too hot. Before switching on the kettle always

check that there is water inside the kettle and the water level is not too low.

• Fill the kettle with cold water only.

• Switch the kettle off before removing it from the base.

• The kettle must be used only with the base provided.

• If the kettle is overfilled, boiling water may be ejected.

Operation

NOTE: Boil and pour away water several times before using for the first time. See recommendations below on

how to operate the kettle.

1. Place the kettle with its base on a dry, smooth and flat horizontal surface. Place the kettle on heat resistant

surfaces only.

2. Take the kettle from the base, open the lid and fill the kettle with cold water.

3. Make sure that the water level is between the minimum and maximum marks on the water level scale. Do

not switch on the kettle when empty.

4. Check and correct the filter’s position before boiling the water.

5. Close the lid and place the kettle back on the base.

6. Plug to AC outlet with the voltage corresponded to the information on the product label.

7. Switch the kettle on by the on/off switch. The illumination light will go on showing that the water is being

boiled.

8. When pouring out the water incline the kettle slightly and gradually. Do not forget that hot water is inside.

Cleaning and Care

1. Unplug the kettle and wait until it cools down completely before cleaning or storing.

2. To avoid the risk of electric shock, do not clean the exterior of the unit, its base or its power cord with water,

and do not immerse it in water. The exterior of the kettle may be cleaned with a slightly damp non-abrasive

lint-free cloth without additives.

3. The filter may be removed for cleaning purposes. To do this, place the filter vertically, pull upwards and draw

out. Wash the outside of the filter in the water flow.

4. Refit all parts when they are completely dry.

5. In the hard water area, it is important to do the decalcification regularly to keep the kettle in good working

condition, because too much scale inside may cause the kettle fail to work. For the best performance of your

kettle, decalcify the unit from time to time. The frequency depends on the hardness of your tap water and

how many times you have used the kettle. Decalcification will clean the interior of the unit.

Missbrauch melden von Frage und/oder Antwort

Libble nimmt den Missbrauch seiner Dienste sehr ernst. Wir setzen uns dafür ein, derartige Missbrauchsfälle gemäß den Gesetzen Ihres Heimatlandes zu behandeln. Wenn Sie eine Meldung übermitteln, überprüfen wir Ihre Informationen und ergreifen entsprechende Maßnahmen. Wir melden uns nur dann wieder bei Ihnen, wenn wir weitere Einzelheiten wissen müssen oder weitere Informationen für Sie haben.

Klarstein 10030984 Seite 6

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Missbrauch melden von Frage und/oder Antwort

Art des Missbrauchs:

Forenregeln

Neu registrieren

Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Ihre Frage wurde zu diesem Forum hinzugefügt

Info