Bedienungsanleitung Klipsch AWR-650-SM (Seite 2 von 4) (Englisch)

581480

Zoom out

Zoom in

Vorherige Seite

1/4

Nächste Seite

Red

- OR -

Green

Right Channel

–

White

Black

Left Channel

–

Red

White

Green

Black

–

White

Red

Black

Green

Klipsch All-Weather Rock Speakers

Thank you for your purchase of this Klipsch Rock Speaker. The

Klipsch All-Weather Rock speaker (AWR-650-SM) is a two-way, dual

channel design using a single high performance bass driver for the low

frequencies and a pair of Polymer dome high frequency tweeters for

wide, even coverage.

The AWR-650-SM can be configured as a single two channel speaker

or used in pairs as a single channel speaker. The AWR-650-SM is

constructed of durable weather proof materials such as a fiberglass

enclosure and powder coated aluminum grilles, a polymer woofer

cone and polymer dome tweeters. This ensures that the speaker will

look and sound good for years to come regardless of environmental

extremes.

Please be sure to fill out the warranty card included with this manual or

online at www.klipsch.com so we are better able to serve you.

Placement

The Klipsch All-Weather Rock speaker is perfect for lawns, gardens,

patios, decks or any other place where exposure to the elements

makes conventional loudspeaker usage unsuitable. Due to its aesthetic

design and up-tilted orientation, this model is designed for low or

ground level placement.

To achieve the best performance from a pair of AWR-650-SMs place

them on the same side of your intended listening area and space them

8 to 20 feet apart. For a higher quality stereo image some degree of

toe-in, toward the primary listening area, may be required to achieve

the desired effect.

If a single AWR-650-SM is connected in a two channel configuration it

is best to center the speaker on the preferred side for even coverage.

Some additional Bass will result if you place the speakers in a corner

or near a wall.

Connections

Important:

Proper connection of your speakers to your

amplifier is vital to obtaining good sound quality. Please

follow these directions carefully.

The AWR-650-SM is provided with a 4-conductor cable to be able to

connect either 1 or 2 channels. One input uses RED for positive and

GREEN for negative, the other uses WHITE for positive and BLACK

for negative. When connecting only 1 channel to the AWR-650-SM

the RED and WHITE must be connected together for positive and

BLACK and GREEN together for negative. Positive(s) and negative(s)

on the speaker must be connected to the positive(s) and negative(s)

respectively for your receiver/amplifier for correct phasing.

Important:

Each channel on the AWR-650-SM has 8

ohm impedance. When joining the inputs for a 1 channel

connection as previously described and shown below, the

AWR-650-SM becomes a 4 ohm speaker. Make sure your

receiver/amplifier can accept a 4 ohm (which most can).

2 Channel Wiring

1 Channel Wiring

Wire Splicing

Unless the AWR-650-SM will be connected to an amplifier/receiver

directly using the 5’ lead, wire splicing to a separate set of high quality,

moisture resistant speaker cable will be required. Follow the following

steps to connect the AWR-650-SM to an amplifier/receiver as a single

channel speaker.

1. Strip away two to three inches of the AWR-650-SM 5' speaker lead

outer jacket away from the individual insulated conducts.

2. Strip one half inch from each of the 4 individual conductors.

3. Twist together the stripped ends of the AWR-650-SM BLACK

(negative) wire AND the AWR-650-SM GREEN (negative) wire AND

the stripped end of the speaker wire connected to the negative

output of the desired channel of the amplifier/receiver.

4. Cap the three wire combination with a silicon filled wire nut. The

material inside the wire nut will protect the stripped ends of the wire

from moisture. If additional protection is desired, additional silicon

(sold separately) can be added to the bottom of the wire nut to

further seal the connection.

5. Repeat steps 3 & 4 for the positive connection of the same channel

using the AWR-650-SM RED (positive) wire AND the AWR-650-SM

WHITE (positive) wire and speaker wire connected to the positive

output of the amplifier/receiver.

To connect the AWR-650-SM as a dual channel stereo speaker

two additional wire nuts will be required (sold separately). Make 4

individual splices, referring to the diagram above, and always double

check that the positive leads of the AWR-650-SM are connected to

the positive outputs of the amplifier/receiver and the negative leads

of the AWR-650-SM are connected to the negative outputs of the

amplifier/receiver.

WARNING:

If channel 1 and 2 are wired out of phase,

the woofer will make little to no sound. This can damage the

woofer if left wired in this manner.

Red

- OR -

Green

Right Channel

–

White

Black

Left Channel

–

Red

White

Green

Black

–

Green

Red

Black

White

Right Channel

Left Channel

Missbrauch melden von Frage und/oder Antwort

Libble nimmt den Missbrauch seiner Dienste sehr ernst. Wir setzen uns dafür ein, derartige Missbrauchsfälle gemäß den Gesetzen Ihres Heimatlandes zu behandeln. Wenn Sie eine Meldung übermitteln, überprüfen wir Ihre Informationen und ergreifen entsprechende Maßnahmen. Wir melden uns nur dann wieder bei Ihnen, wenn wir weitere Einzelheiten wissen müssen oder weitere Informationen für Sie haben.

Klipsch AWR-650-SM Seite 2

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Missbrauch melden von Frage und/oder Antwort

Art des Missbrauchs:

Forenregeln

Neu registrieren

Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Ihre Frage wurde zu diesem Forum hinzugefügt

Info