Bedienungsanleitung Klipsch IC-650-T (Seite 2 von 6) (Englisch)

584719

Zoom out

Zoom in

Vorherige Seite

1/6

Nächste Seite

3. To install the tilebridge, fold the rail side of the ring back

upon itself using the spring tensioner on the reinforcement ring

to allow insertion into the cutout hole. Once it is inserted into

the cutout hole, release the reinforcement ring such that it

unfolds back to its normal position. Position tilebridge over

cutout hole, and insure that the tile rails rest on the t-grid struts.

4. The wiring compartment is intended as a termination point

for the audio circuit. Access to this compartment is gained by

removing the terminal cover located on the back of the

speaker. The terminal cover will accept the appropriate

conduit/wire adapter (provided). Feed wires through

conduit/wire adapter and connect to the input terminal

according to the desired operation mode. Be sure to observe

proper polarity. Replace the terminal cover and tighten the

conduit/wire adapter to secure the wire.

Caution: When connecting 70V or 100V distributed

line systems, take care to ensure proper terminal

connection. Connection to the low impedance termi-

nal could result in speaker damage, amplifier

damage, or both.

Thank you for purchasing your Klipsch IC-400-T,

IC-525-T or IC-650-T in-ceiling speakers.

The IC-400-T, IC-525-T and IC-650-T in-ceiling speakers have been

designed for music reinforcement applications. Unobtrusive,

these loudspeakers are engineered for easy, versatile installation.

The IC-400-T, IC-525-T and IC-650-T feature an internal transformer

for 70V/100V distributed-line systems. The transformer taps are

selected using a rotary switch located conveniently under the

grille. For applications where 8 ohm operation is required, the

transformer can be by-passed by using an optional connection

located on the back input terminal and selectin 8 Ohm on the

front switch.

Before installing your speakers take a moment to check the

contents of the cartons and make sure nothing has been

damaged in transit.

Contents Description QUANTITY

Speaker Modules 2

Grille 2

Reinforcement Ring 2

Rails 4

Cardboard Cutout Template and Paint Mask 2

Screws (Attach Rails to Reinforcement Ring) 8

3/4" Adapter Fittings 2

Installation Guidelines

The IC-400-T, IC-525-T and IC-650-T include a tilebridge for use

when installing the loudspeaker into suspended ceilings or wher-

ever additional reinforcement of the ceiling material is required.

The tilebridge and loudspeaker are designed such that installa-

tion may be accomplished where access above the ceiling is

not possible or may be difficult.

Installation

1. The tilebridge is composed of three parts—a reinforcement ring

and two rails. The two rails should be attached to the reinforce-

ment ring using the four included screws as shown below.

Caution: Be sure to comply with any and all building codes

in your area.

2. To install your IC-400-T, IC-525-T or IC-650-T cut out a hole in the

ceiling using either the cardboard cutout template provided with

your speakers or consult the measurements below. Pull wiring

through hole.

IC-400-T, IC-525-T & IC-650-T

IC-400-T, IC-525-T 9.125 "Round

IC-650-T 10.125 "Round

Missbrauch melden von Frage und/oder Antwort

Libble nimmt den Missbrauch seiner Dienste sehr ernst. Wir setzen uns dafür ein, derartige Missbrauchsfälle gemäß den Gesetzen Ihres Heimatlandes zu behandeln. Wenn Sie eine Meldung übermitteln, überprüfen wir Ihre Informationen und ergreifen entsprechende Maßnahmen. Wir melden uns nur dann wieder bei Ihnen, wenn wir weitere Einzelheiten wissen müssen oder weitere Informationen für Sie haben.

Klipsch IC-650-T Seite 2

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Missbrauch melden von Frage und/oder Antwort

Art des Missbrauchs:

Forenregeln

Neu registrieren

Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Ihre Frage wurde zu diesem Forum hinzugefügt

Info