Bedienungsanleitung Klipsch iFi Speaker System (Seite 3 von 6) (Englisch)

584732

Zoom out

Zoom in

Vorherige Seite

1/6

Nächste Seite

iFi SPEAKER SYSTEM

Auxiliary Audio Input

The control dock also has a 3.5mm stereo minijack auxiliary audio

input on its back panel. It allows you to listen to an external source

(a portable CD player, for example) through the system. When a

plug is inserted in this jack, the system automatically switches to

the auxiliary input. To switch back to the iPod, disconnect the

auxiliary input.

A similar input on the subwoofer’s back panel can also be used

with an external source, but it is primarily intended to connect to

the audio output of a computer.This input is mixed with the

signal from the dock, whether from the iPod or from the

auxiliary input so that both sources are heard simultaneously.

This allows for,as an example, the sound from your computer to

be heard while music is playing from an iPod in the dock.

Subwoofer and Speaker Placement

Although you can place the components of the iFi system almost

any way that is convenient, speaker location will affect sound

quality.The subwoofer will generally perform best when placed on

the floor in a corner.A good second option is to place it 6 to 12

inches from a wall. The farther it is moved toward the middle of

the room, the lower the bass output will be.

You will get the best stereo effect with the satellite speakers

placed equidistant from the listening position. Wide separation will

tend to make the sound more spacious. If possible, avoid locating

either satellite closer than two feet from a side wall. Place them at

seated ear height. If that is not practical, adjust the stands’ ball

joints to aim the satellites up or down toward the listening position.

Stand Adjustment and Wall Mounting

The speakers attach to their stands via a ball joint that allows them

to be swiveled over a wide range. To adjust the angle, un-snap the

supplied hex wrench from underneath the base, loosen the four

screws in the clamp plate that surrounds the ball joint. Position the

speakers as desired and tighten the four clamp screws. Do not

over tighten! Each stand also incorporates an adjustable down stop

to prevent the speaker from drooping after its angle is adjusted.

You can access the head of this down stop from the bottom side

of the stand.

Also on the underside of the base are three (3) keyholes that

enable the stand to function as a wall mount. To install, follow the

instructions below:

1. Using a #2 Philips screwdriver, remove the four (4) screws

that attach the oval metal plate to the bottom the

speaker base.

2. Using the metal plate as a template, mark the screw

locations for the three (3) keyhole slots in the desired

location on the wall. The single keyhole slot must be located

at the top.

3. Screw #8 pan head wood screws (at least two inches/

51mm long) into a wood stud or dry wall anchors with a 20

pound (9 kg) or greater load rating. Leave the screw heads

protruding from the wall surface approximately 1/4" (~7mm).

4. Make sure the small rubber feet are facing the wall and

place the oval metal plate onto the screws through the key

hole slots. Slide the metal plate down into position and

adjust the tightness of the screws for a snug fit.

5. Remove the metal plate from the wall by sliding it up and off

the screws.

6. Remove the logo from the speaker base by compressing its

split post on the underside and rotate it 180°for

proper orientation.

7. Replace the oval metal plate onto the base of the speaker

using the four (4) screws removed in Step #1. Do

not over-tighten!

8. Remove the included hex wrench from the underside of the

speaker base. Loosen the four hex head screws on the

speaker’s ball joint assembly and rotate the base up and

behind the speaker.

9. Gently tighten the four ball joint screws to secure the

speaker’s position. You may need to fine-tune the speaker’s

angle after mounting it to the wall.

10. Hook the speaker base keyholes on the screw heads

protruding from the wall. Slide the base downward onto the

screws to lock the speaker in place.

11. If the speaker will be mounted over the location where the

speaker wire emerges from the wall, thread the wire through

the hole in the speaker base by removing the cosmetic plug.

12. Connect the speaker wire to the speakers binding posts.

13. Fine tune the speaker’s angle and tighten the ball socket

hex screws with the wrench. Do not over-tighten!

14. Store the hex wrench in the bottom of the base cover by

snapping it into the speaker base.

Missbrauch melden von Frage und/oder Antwort

Libble nimmt den Missbrauch seiner Dienste sehr ernst. Wir setzen uns dafür ein, derartige Missbrauchsfälle gemäß den Gesetzen Ihres Heimatlandes zu behandeln. Wenn Sie eine Meldung übermitteln, überprüfen wir Ihre Informationen und ergreifen entsprechende Maßnahmen. Wir melden uns nur dann wieder bei Ihnen, wenn wir weitere Einzelheiten wissen müssen oder weitere Informationen für Sie haben.

Klipsch iFi Speaker System Seite 3

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Missbrauch melden von Frage und/oder Antwort

Art des Missbrauchs:

Forenregeln

Neu registrieren

Andere Handbücher von Klipsch iFi Speaker System

Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Ihre Frage wurde zu diesem Forum hinzugefügt

Info