Bedienungsanleitung Klipsch KSW (Seite 12 von 16) (Englisch)

584795

Zoom out

Zoom in

Vorherige Seite

1/16

Nächste Seite

Subwoofer Placement

Your Klipsch subwoofer is designed to operate at frequencies below 120Hz, which are essentially

omnidirectional (difﬁcult to localize). There may be several options for placement of the subwoofer in

your room that will effect its frequency response and output level. Corner placement improves the

acoustic loading of the subwoofer, increasing its output and dynamic range capabilities. Placing the

subwoofer away from walls or in the center of the room will result in the least amount of output.

Asymmetrical placement of two subwoofers in a room may improve low frequency reproduction by

providing a smoother and more consistent response pattern. Since even minor repositioning will result

in an audible performance change due to room acoustics, Klipsch recommends experimentation with

the subwoofer placement in the room.

A general rule of thumb is to place your subwoofer in the vicinity of the speakers with which it is

being paired. For example, a subwoofer reproducing front channel bass will generally perform better

when placed in the same end of the room as the main speakers. As well, a subwoofer connected to

the rear channels of a surround system performs best when positioned in the rear of the room.

If the subwoofer is installed near your television and color distortion is noted, simply move the sub-

woofer farther away from your television until the interference disappears.

If your subwoofer is placed in an enclosed cabinet, provisions must be made to ventilate the heat

radiated by the enclosed ampliﬁer. Additionally, since some of the acoustic output is generated by the

sub’s rear ﬁring port, a minimum of several inches of space should be provided around the sub-

woofer. If the front of the cabinet is acoustically open, the back of the subwoofer, with the port and

ampliﬁer controls, should be oriented in this direction.

If your subwoofer will be used on a hard, non-carpeted surface, attach the enclosed rubber pads to

the subwoofer’s feet to prevent vibration and marring.

How to Connect Your

KSW Series Subwoofer

AC Power

Since your KSW subwoofer has an internal power ampliﬁer, it must be plugged into a nearby AC wall

outlet. The subwoofer should be unplugged from the AC power with the power switch in the OFF posi-

tion during hookup and installation. To eliminate a tripping hazard, all connections should be

unplugged from the back panel of the subwoofer if it is being moved. Avoid extremely long extension

cords of small gauge since they may impair the performance of the subwoofer ampliﬁer and present a

potential ﬁre hazard. If the subwoofer will not be used for an extended period of time, unplug the

power cord from the AC power outlet.

Note: 230 volt models are not supplied with an AC power cord, but are equipped with an IEC-type

power cord socket.

CAUTION: SINCE YOUR KLIPSCH SUBWOOFER HAS BUILT-IN ELECTRONICS, DO NOT

PLACE IT NEAR SOURCES OF HEAT OR MOISTURE! TAKE CARE TO ROUTE THE POWER

CORD SO THAT IT WILL NOT BE CUT, DAMAGED OR PINCHED.

Types of Connections

Your subwoofer may be installed using either the SPEAKER LEVEL or LINE LEVEL connection, but

not both. The LFE connection is an optional line level connection that can be used in conjunction

with either type of hookup. Refer to the “LFE IN / BYPASS IN” and “BASS MANAGEMENT” sec-

tions for more detail. You can connect the subwoofer so that your main speakers will reproduce a full

range signal (all models) or a limited range (bass ﬁltered) signal (KSW 12 and KSW 15 only). Speaker

level connections are used when connecting to a receiver or integrated ampliﬁer that lacks line level

subwoofer or pre-amp output jacks. Line level connections are often the best choice when connecting

the subwoofer to a system comprised of a separate pre-amp/processor and power ampliﬁer. This also

applies to any receiver or integrated ampliﬁer that possesses main channel pre-amp or subwoofer

outputs. The type of connection conﬁguration used depends upon the capabilities of your equipment

and your performance goals.

Missbrauch melden von Frage und/oder Antwort

Libble nimmt den Missbrauch seiner Dienste sehr ernst. Wir setzen uns dafür ein, derartige Missbrauchsfälle gemäß den Gesetzen Ihres Heimatlandes zu behandeln. Wenn Sie eine Meldung übermitteln, überprüfen wir Ihre Informationen und ergreifen entsprechende Maßnahmen. Wir melden uns nur dann wieder bei Ihnen, wenn wir weitere Einzelheiten wissen müssen oder weitere Informationen für Sie haben.

Klipsch KSW Seite 12

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Missbrauch melden von Frage und/oder Antwort

Art des Missbrauchs:

Forenregeln

Neu registrieren

Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Ihre Frage wurde zu diesem Forum hinzugefügt

Info