Bedienungsanleitung Klipsch P-312W (Seite 6 von 9) (Englisch)

584805

Zoom out

Zoom in

Vorherige Seite

1/9

Nächste Seite

Page 10 Page 11

Keypad Lock

This screen is used to lock the keypad and prevent unintentional changes to your settings by other users. After

making all desired adjustments, press the Enter key to lock the keypad. “Keypad Locked Hold   to Unlock”

will be displayed. The display will then return to the default “Volume” screen after about 20 seconds. To unlock

the keypad, press and hold the Left and Right touch keys until the display returns to the “Volume” screen. The

keypad is now unlocked. It is suggested that you write down all of your settings for future reference in case the

keypad is unlocked and your settings are changed by another user. From this screen, press the Down or Up

touch key to access other control settings.

System Info Press 

This screen is used to access the software “Version” number and “System Reset” function to clear all user settings

and memories (Refer to the “Save Settings” section of this manual). If the “System Reset” function is activated all

of the memory presets are erased and the subwoofer’s controls are restored to the default settings of: “Volume

0db”, “EQ Mode Flat”, “Lowpass O LFE Mode”, “Phase 0°”, “Disp Brightness” (highest level) and “Power Always On.

For more information on the controls mentioned in this manual and on the bass management settings

of your electronics, see your authorized Klipsch dealer or visit www.klipsch.com.

Features and Controls - 4

This section describes the features and connections found on the amplier on the back panel of the subwoofer.

It also describes the manner for connecting a second subwoofer as a “slave” unit to the primary subwoofer.

Power On/O

This is the main AC power switch for the subwoofer. This

switch must be in the “On” position for the subwoofer to

operate and for the “Auto On” feature to function. Set this

switch to the “O” position if the subwoofer will not be used

for an extended period of time (i.e. vacation) or when mak-

ing any connections to the subwoofer.

USB

This USB computer interface allows access to additional

advanced features within the subwoofer’s ARC room

correction software. Optional, proprietary Klipsch software

and a higher level of technical knowledge are required to

correctly utilize this capability. This port can also function as an

alternative control interface with A/V control systems that can

utilize a USB connection. Please contact your authorized Klip-

sch dealer or Klipsch Technical Support for more information.

Line Out

There are both RCA-type and XLR connections provided for line out signals. Choose the one appropriate for your

system. Do not use both at the same time. This connection can be used as an alternate connection point for a

second subwoofer as opposed to connecting them both to your electronics. Be aware that the signal output from

these jacks is aected by the “Volume”, “EQ”, “Lowpass”, “Lowpass Slope”, “Phase” and “Room Correction” settings of

your Palladium subwoofer. The advantage of this is the ability of the Adaptive Room Correction (ARC) function to

correct the response of the second subwoofer resulting in a more accurate response. If the second subwoofer is

connected directly to your system, the Palladium subwoofer’s ARC will react to, rather than control, the response

of the other subwoofer. As a result, we recommend the following procedure when connecting a second sub-

woofer to these outputs:

• Play a signal, such as one of the Palladium subwoofer’s two demo tracks and set the volume control of the

second subwoofer to approximately match that of the Palladium subwoofer.

• Defeat the secondary subwoofer’s lowpass setting by selecting the “Bypass” or “LFE” mode or set the lowpass

control to its highest frequency if these options are not present.

• Set the secondary subwoofer’s phase control to 0°.

• Run the “Room Correction” function on the Palladium subwoofer.

• As with the initial setup of your Palladium subwoofer, listen to a track with a repeating bass line in your listen-

ing position. Experiment with alternate phase settings on the secondary sub, while repeating this track. If

one of these alternate settings yields an increased amount of bass, choose that setting and run the Palladium

subwoofer’s room correction function again.

• Please note that if either the volume or phase settings on the secondary sub are changed after running the

ARC function, you will have to either reset them to the location they were at when the room correction was

performed or run the ARC calibration again to compensate.

Back Panel Features

Missbrauch melden von Frage und/oder Antwort

Libble nimmt den Missbrauch seiner Dienste sehr ernst. Wir setzen uns dafür ein, derartige Missbrauchsfälle gemäß den Gesetzen Ihres Heimatlandes zu behandeln. Wenn Sie eine Meldung übermitteln, überprüfen wir Ihre Informationen und ergreifen entsprechende Maßnahmen. Wir melden uns nur dann wieder bei Ihnen, wenn wir weitere Einzelheiten wissen müssen oder weitere Informationen für Sie haben.

Klipsch P-312W Seite 6

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Missbrauch melden von Frage und/oder Antwort

Art des Missbrauchs:

Forenregeln

Neu registrieren

Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Ihre Frage wurde zu diesem Forum hinzugefügt

Info