Bedienungsanleitung Klipsch P-38F (Seite 7 von 11) (Englisch)

584807

Zoom out

Zoom in

Vorherige Seite

1/11

Nächste Seite

Page 12 Page 13

Final AdjustmentsFinalizing the Assembly

The Palladium Series loudspeakers have a phenomenal frequency response and superb dynamics, so playing

large orchestral or rock music will be an awesome experience, but may not necessarily be the best guide in

setting up the speakers. Your listening tests should be performed with a wide range of music, including unac-

companied vocal and solo instrumental recordings with as little processing on the source as possible. A natural

solo cello recording will reveal much about the bass characteristics of your room and positioning. The best

position will yield smooth, extended bass without boom or smear.

Stridency in the upper section caused by underdamped rooms can be compensated for by hanging drapes or

pictures on the walls to dampen reverberant walls; increasing the amount of soft furnishings will also help to

eliminate high frequency “ringing”.

Room resonances are often structural. In such circumstances, good placement will minimize but not eliminate

these resonances.

Apparent height is critical. The speakers have controlled directivity. Phase response anomalies are kept to

vanishingly low levels by reducing the distance between the midrange and tweeter horns to the absolute

minimum; nevertheless, if you are in the wrong seat, it may happen that the sound stage is not perfectly inte-

grated. One remedy is to tilt the speaker slightly (if necessary by using a combination of long and short spikes)

to aim the midrange driver at the listener’s ear to yield best driver integration. Take your time with this —the

eects on some music may be small and quite startling on others.

Phase

Phase is not a matter of preference. Out-of-phase eects manifest themselves as poorly dened bass, poor

stereo with very vague localization of instruments and voice, and generally fuzzy, ill-dened sound. A single-

wired out of phase system is easy to detect; a bi-amped system with one element connected out of phase

can be nearly impossible to track down. If you nd that there are problems with the system that no amount of

experimentation can cure, check all the loudspeaker and amplier wiring carefully. If you have connected your

speakers strictly in accordance with this manual, no phase problems will arise.

Conclusion

All the advice above will help you get the most out of these superb loudspeakers, but in the nal analysis you

should do what your ears tell you is right—you are, after all, the nal arbiter of your system.

Happy listening!

Fitting Spikes (P-38F and P-37F only)

The loudspeakers are supplied with a set of long spikes and a

set of short spikes. All are adjustable and t in the same way.

Spike seats with felt bases are supplied for use where spikes

are inappropriate; e.g., on stone, hardwood or marble oors.

The spikes may be tted with sets of short spikes, sets of

long spikes or as a combination of two short spikes at the

front and two long spikes at the rear to assist with imaging,

(Refer to the next page)

Fitting Spikes (P-27C only)

The P-27C also has spikes that should be used if the speaker

is not placed on a dedicated speaker stand. There are two

short front spikes with spike seats that should be installed

in the same manner as described above for the P-38F and P-37F. There is a third spike seat for use with either

of the two rear spikes. The long-barrel rear spike should be used in applications where the speaker needs to be

positioned either at or with a degree of downward tilt. The short-barrel rear spike should be used in applications

where the speaker needs to be positioned with a degree of upward tilt. This will often be the case in installations

where the speaker is placed below a large projection screen.

Method: Run the textured collar halfway down the threaded shaft away from the spike point. Insert the shaft into

the plinth and screw in tight. Now run the collar up to the plinth and lock it nger tight. Repeat for all four spikes.

Hint: If you feel that you may have to move the speakers around a lot before you get them exactly right, it is advisable

to start out with the spikes resting in their spike seats. This will allow you to easily slide the speakers on a hard oor

surface After nalizing the speaker position, you can then mark the position of the feet and remove the spike seats.

Dressing the Cables

If there is more than one cable to each loudspeaker, gather them and lay them side by side. Make sure you have

identication on all the cables. Ensure the cables are connected the same way all around with no loose or faulty

connections.

Leveling the Loudspeakers

If the oor is not perfectly level, you will nd that one spike is o the ground. Starting with this spike and with the

help of a spirit level, you should now adjust the spikes so the speakers do not wobble and are not at an angle. Try

to get the speakers to the same height, if at all possible.

Final Connections

Now, connect the loudspeakers to the amplier/s using the diagrams on pages 8-11 to help you.

You are now ready to enjoy your music!

Collar

Spike

Shaft

Spike Seat

Missbrauch melden von Frage und/oder Antwort

Libble nimmt den Missbrauch seiner Dienste sehr ernst. Wir setzen uns dafür ein, derartige Missbrauchsfälle gemäß den Gesetzen Ihres Heimatlandes zu behandeln. Wenn Sie eine Meldung übermitteln, überprüfen wir Ihre Informationen und ergreifen entsprechende Maßnahmen. Wir melden uns nur dann wieder bei Ihnen, wenn wir weitere Einzelheiten wissen müssen oder weitere Informationen für Sie haben.

Klipsch P-38F Seite 7

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Missbrauch melden von Frage und/oder Antwort

Art des Missbrauchs:

Forenregeln

Neu registrieren

Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Ihre Frage wurde zu diesem Forum hinzugefügt

Info