Bedienungsanleitung Klipsch R-112SW (Seite 6 von 48) (Deutsch, Englisch, Französisch, Italienisch, Portugiesisch, Spanisch)

584829

Zoom out

Zoom in

Vorherige Seite

1/48

Nächste Seite

CONNECTIONS AND CONTROLS

CAUTION: Ensure that the subwoofer is unplugged from the AC wall outlet

before making any connections.

“LINE IN” Connection - Most of today’s surround receivers (and pre-

ampliﬁers) have a line level subwoofer output labeled Subwoofer Pre Out,

Sub Out, SW Out, etc. If you have this output, connect one end of a subwoofer

cable to it and connect the other end of the cable into the subwoofer line

input labeled LEFT/LFE. This connection allows the subwoofer to operate

with both music and surround sound movies (refer to your receiver manual).

In absence of a subwoofer output on your receiver, as an alternative hookup,

you can connect Left and Right channel Pre-Amp Outputs from your receiver

(if provided) to the Left/LFE and Right input on the subwoofer.

WA-2 Port Connection - For wireless connectivity of your new Klipsch

R-110SW, R-112SW, or R-115SW subwoofer, the optional WA-2 is available. The

WA-2 will only operate with select Klipsch, Energy, Mirage and Jamo brand

subwoofers that have a “WA Port” input. The WA-2 is a 2.4 GHz product

designed to wirelessly transmit a signal up to a 50 foot radius. See klipsch.

com for more details.

Level - If your subwoofer is connected to a Subwoofer Output of a surround

receiver, ﬁrst set the subwoofer volume level control in the receiver to the

“half way” or “0 dB” position. Then increase the volume (or gain) of the

subwoofer up until the subwoofer’s volume level matches the output of your

main speakers. After this setup is completed, the volume control on your

system’s main ampliﬁer or pre-ampliﬁer will be the volume control for both

your subwoofer and speakers together. If your subwoofer is connected to the

L/R Pre-Amp Outputs of a receiver there will be no subwoofer volume in that

receiver to set before setting the subwoofer’s gain control.

“LOWPASS” Control - The crossover point chosen determines where low

bass frequencies are “handed off” from the speakers to the subwoofer. If

setting the crossover point in the receiver, turn the Lowpass Filter knob on

the subwoofer to the farthest point right (160Hz). Set the crossover point

based on the size of the main left/right speakers you are using in the system.

As a general rule, for larger, ﬂoorstanding speakers, set the crossover point

between 50Hz-90Hz. If using small bookshelf or “satellite” speakers for

the mains, set the crossover point between 90Hz-150Hz. The smaller the

speaker, the higher the setting until the bass frequencies blend well between

the speakers and your subwoofer once your system is completely hooked

up. If your receiver does not have a crossover point setting, set the Lowpass

Filter on the subwoofer instead within the same recommended settings (see

receiver manual for additional speaker setup info).

“PHASE” 0/180 - This control is used to acoustically match the subwoofer’s

output to your main speakers. Select the position, either 0° or 180°, in which

your subwoofer has more output at the listening position.

“POWER” AUTO/ON/OFF -

When this switch is in the “ON/AUTO/STANDBY”

position, the subwoofer will automatically turn “on” when it senses a signal. It

will automatically go into “standby mode” after 15-20 minutes with no signal.

When this switch is in the “OFF” position, the subwoofer will remain “off” until

the switch is manually turned back to the “ON/AUTO/STANDBY” position.

Power LED indicator - Located on the front bafﬂe, this LED indicates the

operating status of the built-in ampliﬁer. The LED will light green when

the ampliﬁer is on and receiving a signal. If the LED is dark and not lit, the

ampliﬁer is off. For more information on the controls mentioned in this

manual and on bass management, see your dealer or visit www.klipsch.com

Missbrauch melden von Frage und/oder Antwort

Libble nimmt den Missbrauch seiner Dienste sehr ernst. Wir setzen uns dafür ein, derartige Missbrauchsfälle gemäß den Gesetzen Ihres Heimatlandes zu behandeln. Wenn Sie eine Meldung übermitteln, überprüfen wir Ihre Informationen und ergreifen entsprechende Maßnahmen. Wir melden uns nur dann wieder bei Ihnen, wenn wir weitere Einzelheiten wissen müssen oder weitere Informationen für Sie haben.

Klipsch R-112SW Seite 6

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Missbrauch melden von Frage und/oder Antwort

Art des Missbrauchs:

Forenregeln

Neu registrieren

Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Ihre Frage wurde zu diesem Forum hinzugefügt

Info