Bedienungsanleitung Klipsch R-25C (Seite 6 von 48) (Deutsch, Englisch, Französisch, Italienisch, Portugiesisch, Spanisch)

588307

Zoom out

Zoom in

Vorherige Seite

1/48

Nächste Seite

ROOM PLACEMENT CONNECTION

Left and Right Main Channel Speakers — For optimum

performance, Klipsch Group, Inc. (KGI) suggests placing your

speakers 6 to 15 feet (1.8 to 4.6m) apart. They may also be toed-in

slightly for better stereo imaging. The listening position should be

about 1 to 1.5 times the distance separating the speakers. Refer to

Figures 1 and 3 for connection and placement.

Center Channel Speakers — Center channel speakers are designed to

place dialogue and primary sounds so that they appear to come from

the video screen. The speakers should therefore be placed as close

to the screen as possible, preferably directly on top of or below the

screen. Refer to Figures 1, 2 and 3 for connection and placement.

Rear Surround Channel Speakers — Klipsch WDST surround speakers

should be placed approximately 2 feet above the listening position.

Typically this will be about 5-7 feet above the ﬂoor. The surrounds

should be placed on the walls directly adjacent to the listening position.

Another option would be on the wall behind the listening position.

The ﬁnal surround speaker placement depends on your room’s

characteristics. They are designed to recreate the sense of space and

ambience that many of today’s surround sound technologies provide.

Refer to Figures 1, 3 and 4 for connection and placement.

Please note that surround grilles are ﬁxed and cannot be removed.

Conventional Connection — Using 16-12 gauge speaker wire, connect

the RED “positive” (+) terminal of the LEFT speaker to the RED

“positive” (+) terminal of your ampliﬁer’s LEFT channel. Connect the

BLACK “negative” (–) terminal of the LEFT speaker to the BLACK

“negative” (–) terminal of your ampliﬁer’s LEFT channel. Repeat this

procedure for connecting all remaining speakers to the appropriate

ampliﬁer channels. Refer to Figure 3. Make sure that no bare wires

from any of the connections touch any other terminals as this could

cause a short and damage your equipment.

Some Klipsch Reference speakers come with dual binding posts that

are connected by a metal strip. Do not remove this strip or your

speakers will not function correctly. Keep this strip in place and

connect your speaker wire to the top set of the binding posts. It is

possible to “Bi-wire” a speaker that has two sets of binding posts.

Please see your receiver’s manual for further instructions.

Ampliﬁer Requirements — Klipsch speakers are highly efﬁcient and

will operate easily on a wide variety of ampliﬁers. All Klipsch speakers

are 8-ohm compatible and can be driven to very high levels with low

distortion. Due to the high output levels Klipsch speakers are capable

of reproducing, exercise caution with the volume control. Excessive

volume over long periods can permanently damage your hearing.

Overdriving your ampliﬁer could also damage your speakers. Check with

your dealer or ampliﬁer manual to make sure your particular ampliﬁer

is best suited to your application. We want you listening for a lifetime.

Missbrauch melden von Frage und/oder Antwort

Libble nimmt den Missbrauch seiner Dienste sehr ernst. Wir setzen uns dafür ein, derartige Missbrauchsfälle gemäß den Gesetzen Ihres Heimatlandes zu behandeln. Wenn Sie eine Meldung übermitteln, überprüfen wir Ihre Informationen und ergreifen entsprechende Maßnahmen. Wir melden uns nur dann wieder bei Ihnen, wenn wir weitere Einzelheiten wissen müssen oder weitere Informationen für Sie haben.

Klipsch R-25C Seite 6

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Missbrauch melden von Frage und/oder Antwort

Art des Missbrauchs:

Forenregeln

Neu registrieren

Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Ihre Frage wurde zu diesem Forum hinzugefügt

Info