Bedienungsanleitung Klipsch RVX (Seite 3 von 27) (Deutsch, Englisch, Französisch, Italienisch, Portugiesisch, Spanisch)

588339

Zoom out

Zoom in

Vorherige Seite

1/27

Nächste Seite

BUT FIRST: TYPES OF CONNECTORS

Bare wire — Pull the two conductors apart for about an inch and strip approximately

1/4”

insulation from the end of each. (A wire stripper will simplify this, but you can use an ordinary

pocket knife to cut around and through the insulation down to the wire.) Twist the strands of wire on

each individual conductor tightly together. Loosen the nuts on a pair of binding posts until the holes

through the metal posts are exposed, then insert the bare wire through the holes. Screw the nuts

down finger-tight on the wire. Make sure that no strands of wire are touching from one binding post

to the other or to any strands from the other conductor. Failure to observe this precaution at either

end of the connection can result in amplifier malfunction or damage.

Pins — Many pre-made speaker cables are terminated with metal pins. Loosen the nuts on a

pair of binding posts until the holes through the metal posts are exposed, then insert the pins

through the holes. Screw the nuts down finger-tight on the pins — do not over-tighten. Make

sure that there is no metal-to-metal contact between the two pins or binding posts. Failure to

observe this precaution at either end of the connection can result in amplifier malfunction or

damage.

Spade lugs — Some speaker cables are terminated with U-shaped connectors called spade

lugs. Loosen the nuts on a pair of binding posts and slip the spade lugs around the metal posts.

Screw the nuts down finger-tight on the lugs and inspect to ensure they have remained firmly

in place. Make sure that there is no metal-to-metal contact between the two lugs or binding

posts. Failure to observe this precaution at either end of the connection can result in amplifier

malfunction or damage.

OTHER TYPES OF SPECIALTY CONNECTORS ARE AVAILABLE TO FACILITATE HOOKING UP YOUR

SPEAKERS. PLEASE CONSULT YOUR AUTHORIZED KLIPSCH DEALER FOR SUGGESTIONS AND

FURTHER DETAILS.

SPEAKERS TO AMPLIFIER: KEEPING IT STRAIGHT

One of the most important things about hooking up your speakers is keeping them in the

same polarity, or phase. If they are connected out of phase, bass and sound localization will

be degraded.

The easiest way to ensure that your speakers are wired in phase is to always connect the

positive and negative output terminals on your amplifier or receiver to the matching input

terminals on your speakers: positive ("+", color-coded red) to positive and negative ("–", color-

coded black) to negative. (See Figure 3).

Most pre-termina

ted speaker ca

bles ha

ve color-coded connectors that make it easy to match

output and inputs correctly. If yours do not, or if you are making your own out of paired,

two-conductor wire,

look f

or identifying marks on the insula

tion of the two conductors.

Normall

y there will be printing,

a stripe or a molded ridge along one of the conductors.

Surround Back Speakers: If your electronics support Dolby Digital EX, THX Surround EX, or DTS-

ES 7.1 or 6.1-channel surround, you can place one or two speakers behind the seating area to

serve as surround back speakers. As with the left and right surrounds, the optimum location is

above seated ear level. If you are using just one back surround speaker, it should be centered

behind the listening area; if you are using two, they should be spaced fairly close together. With

this type of system, the regular left and right surrounds should be located adjacent to the seating

area rather than behind it.

STAND ADJUSTMENT AND WALL MOUNTING

The RVX-42’s attach to their stands via a bolt that allows them to be used in either the vertical ori-

entation as they are shipped for shelf top use or horizontally, as is typical for center channel use.

To adjust the base, remove the stand bolt tool from the rear of the unit and remove the bolt from

the stand. Reposition the stand in the center mounting point and then replace the stand bolt tool

in the opening that the stand bolt was previously installed within. (See Figure 2).

You may also use an optional wall or ceiling mount that will fit the provided 3/8" – 16 inserts.

Please see your authorized Klipsch dealer to determine which model is right for you.

To install the RVX-42, follow the instructions below:

Locate the included wall mount template with bubble level and position on the wall in the desired

location.

Mark the screw loca

tions for the model you are installing.

Screw #8 pan head wood screws (a

t least two inches in length) into a wood stud or dr

y wall

anchors with the appropriate load rating. Leave the screw heads protruding from the wall surface

approximately 1/4” and adjust as needed when hanging the speaker.

Attach the supplied self-stick rubber pads to the rear of the speaker.

Connect the speaker wire to the speakers binding posts. See “Speaker to Amplifier: Keeping it

Flip the switch at the top of the rear of the speaker to “On Wall” for accurate bass response.

Hook the speaker keyholes on the screw heads protruding from the wall. Adjust the height of

the screw heads for a snug fit. Do not over-tighten.

Fine tune the speaker’

s angle if using an optional wall mount tha

t fits the provided 3/8" – 16 inserts.

CONNECTIONS

Note: Proper connection of your speakers to your amplifier or receiver is vital to obtaining good sound

quality. Please follow these directions carefully. Sloppy connections can cause amplifier malfunction

or damage.

Klipsch Reference Series speakers are wired internally with multiple gauges of high-purity copper

wire, carefully selected and wound to ensure optimum signal transfer at all frequencies. You will obtain

best perf

ormance from your speakers if you connect them to your amplifier or receiver with similar

quality wire available from your dealer. We recommend that you use 18-gauge or heavier (lower-

gauge) stranded copper wire. Use a lower gauge (heavier) wire for longer runs to reduce the amount

of amplifier power lost due to the wire’

s resistance.

Figure 2

Figure 3

ENGLISH

straight

Klipsch RVX Seite 3

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Missbrauch melden von Frage und/oder Antwort

Art des Missbrauchs:

Forenregeln

Neu registrieren

Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Ihre Frage wurde zu diesem Forum hinzugefügt

Info