Bedienungsanleitung Klipsch SC-1 (Seite 9 von 12) (Englisch)

588354

Zoom out

Zoom in

Vorherige Seite

1/12

Nächste Seite

Wall Mounting

• Install the four rubber stick-on bumpers (one on each corner of the rear panel of the speaker) to

provide clearance for the speaker wire between the wall and cabinet. This will also prevent the

speaker from marring the wall.

• Cut out the template on the back cover of the owner’s manual to assist in obtaining proper

spacing of the two mounting holes. If the template is not available, space the mounting screws

/16" apart on a vertical line. Allow at least 1

/2" of clearance space above the top screw.

• Check the vertical orientation of the marked hole locations with a torpedo level before drilling.

• Use a #10 or #12 (2

/2 -3"long) pan head wood screw to mount into the wall stud.

•

Check the ﬁt of the screw head in the keyhole ﬁtting before installation as screw head sizes do vary.

• Drill the proper size pilot holes at the marked positions and install the screws into the wall stud.

Leave the back surface of the screw head protruding about

/4-inch from the wall surface. This

will facilitate hooking the keyhole bracket over the screw head with the rubber feet installed. The

clearance between the wall and the screw head may need to be adjusted to achieve a proper ﬁt.

If a stud is not available, use the proper type and weight rating of drywall or masonry anchor

appropriate for the wall construction. Please consult your dealer, custom installer or a building

contractor in this situation.

• Do not use the keyhole mounting brackets for ceiling installations!

How to Connect the Synergy Series Speakers

AC POWER / SP-1 ONLY

Since your SP-1 has an internal subwoofer power ampliﬁer, it must be plugged into a nearby AC wall

outlet. The SP-1 should be unplugged from the AC power with the power switch in the OFF position

during hook up and installation. To eliminate a tripping hazard, all connections should be unplugged

from the back panel of the speaker if it is being moved. Avoid extremely long extension cords of small

gauge since they can impair the performance of the subwoofer ampliﬁer and present a potential ﬁre

hazard. If the SP-1 will not be used for an extended period of time, unplug the power cord from the

AC power outlet.

Note: 230 volt models are not supplied with an AC power cord, but are equipped with an IEC-type

power cord socket.

CAUTION!

Since your Klipsch SP-1 has built-in electronics, do not place it near sources of heat or moisture.

Take care to route the power cord so that it will not be cut, damaged or pinched.

SPEAKER WIRE CONNECTIONS

Switch your electronics OFF when making all connections! When making any type of speaker wire

connection be sure to observe proper polarity (+ to + and - to -). Most speaker wire is insulated,

two-conductor, stranded construction and is color-coded or has some distinguishing feature differen-

tiating the two conductors. Speaker wire connectors on most loudspeakers and ampliﬁers are also

color-coded. Typically, RED is positive (+) and BLACK is negative (-), or ground. It does not matter

which conductor is connected to the positive or negative terminals of your equipment as long as you

are consistent. Be sure that the connections from all of the ampliﬁer channels to all of the speakers in

your system are connected in a like manner. If not, the quantity of bass will be reduced and the

stereo image will be compromised. Be careful not to have excess bare wire or loose strands of wire

at the connections. This could cause a short between adjacent positive and negative terminals, dam-

aging your speakers and ampliﬁer. Eighteen gauge (AWG) wire is the minimum size recommended

for short distances, with larger gauges recommended for longer runs. Consult your Klipsch dealer for

speciﬁc suggestions.

Connect the SB-2, SB-3, SF-1, SF-2 or SP-1 to the “Front” or “Main” channel speaker outputs of

your system’s power ampliﬁer.

Missbrauch melden von Frage und/oder Antwort

Libble nimmt den Missbrauch seiner Dienste sehr ernst. Wir setzen uns dafür ein, derartige Missbrauchsfälle gemäß den Gesetzen Ihres Heimatlandes zu behandeln. Wenn Sie eine Meldung übermitteln, überprüfen wir Ihre Informationen und ergreifen entsprechende Maßnahmen. Wir melden uns nur dann wieder bei Ihnen, wenn wir weitere Einzelheiten wissen müssen oder weitere Informationen für Sie haben.

Klipsch SC-1 Seite 9

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Missbrauch melden von Frage und/oder Antwort

Art des Missbrauchs:

Forenregeln

Neu registrieren

Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Ihre Frage wurde zu diesem Forum hinzugefügt

Info