Bedienungsanleitung Klipsch SS-1 (Seite 11 von 12) (Englisch)

588355

Zoom out

Zoom in

Vorherige Seite

1/12

Nächste Seite

Troubleshooting

• If one or both SP-1 subwoofers have little or no output:

— Double check your power (AC) and system connections.

— Make sure that the power switch on the rear control panels of both units is set to the

“ON” or “AUTO” position.

— Check that the power light on the front of the SP-1 is lit. If not, check the AC fuse. When

changing the AC main’s power fuse, unplug the power cord ﬁrst. To access the fuse, use the

appropriate screwdriver to unscrew the cap on the fuse receptacle. If the fuse is blown (the

ﬁlament inside the glass tube is burned through), replace it with the same type and value as

is printed on the ampliﬁer panel next to the fuse holder. NEVER INSTALL A LARGER

FUSE THAN THE VALUE INDICATED ON THE AMPLIFIER PANEL. If the fuse blows

again when the subwoofer is powered up, return the unit to your authorized Klipsch dealer

for servicing by qualiﬁed personnel. If dealer service is not available, contact Klipsch

customer service for a Return Authorization number before shipping (REQUIRED).

Klipsch Customer Service: 800-554-7724

All return shipments should be made to:

Klipsch, L.L.C.

137 County Road #278

Hope, AR 71801

RA#…(return authorization number required)

• The SP-1’s powered subwoofer ampliﬁer is protected by a thermal sensor. If the unit is run for

extended periods beyond its designated power rating, the thermal sensor will engage and shut

down the subwoofer. If this occurs, turn the “POWER” switch off, turn down the volume on

your electronics and wait ﬁve minutes before restarting the system.

• If you experience a noticeable hum when the SP-1’s subwoofer is connected to your system

(a system that includes video equipment), disconnect the cable television line (if present). If the

hum disappears, consult your Klipsch dealer for a ground isolator for the cable line. If this does

not solve the problem, contact your Klipsch dealer for further advise.

• Regardless of your ampliﬁer’s rated capacity, do not operate the system at the full output (highest

volume): Ampliﬁers can create extremely high levels of distortion when operated at full output

and can damage your loudspeakers. Most ampliﬁers are at full power when the volume control is

at or just above the 12 o’clock position.

• Position speaker connection wires so that they do not create a trip hazard.

If you have any questions regarding the installation or connection of your Klipsch Synergy speakers,

please contact your Klipsch dealer or contact us directly at 800-554-7724.

Care and Cleaning of Your Klipsch

Synergy Speakers

Your speakers have a durable matte vinyl ﬁnish that should only require dry dusting or cleaning

with a damp cloth. Avoid the use of abrasive or solvent-based cleaners and harsh detergents.

Missbrauch melden von Frage und/oder Antwort

Libble nimmt den Missbrauch seiner Dienste sehr ernst. Wir setzen uns dafür ein, derartige Missbrauchsfälle gemäß den Gesetzen Ihres Heimatlandes zu behandeln. Wenn Sie eine Meldung übermitteln, überprüfen wir Ihre Informationen und ergreifen entsprechende Maßnahmen. Wir melden uns nur dann wieder bei Ihnen, wenn wir weitere Einzelheiten wissen müssen oder weitere Informationen für Sie haben.

Klipsch SS-1 Seite 11

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Missbrauch melden von Frage und/oder Antwort

Art des Missbrauchs:

Forenregeln

Neu registrieren

Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Ihre Frage wurde zu diesem Forum hinzugefügt

Info