Bedienungsanleitung Klipsch SS-5 (Seite 8 von 11) (Englisch)

588376

Zoom out

Zoom in

Vorherige Seite

1/11

Nächste Seite

• Locate the wall stud that is the closest to your desired mounting location and drill the proper size

pilot hole in the wall. Allow at least 1

/2" of clearance space between the top of the screw head

and any barrier above it (ceiling or shelf).

• Use a #10 or #12 (2

/2 - 3" long) pan head wood screw to mount into the wall stud.

• Check the ﬁt of the screw head in the keyhole ﬁtting before installation as screw head sizes

do vary.

• Install the screw into the wall stud leaving the back surface of the screw head protruding about

/4-inch from the wall surface. This will facilitate hooking the keyhole bracket over the screw

head with the rubber feet installed. The clearance between the wall and the screw head may need

to be adjusted to achieve a proper ﬁt.

• If a stud is not available, use the proper type and weight rating of drywall or masonry anchor

appropriate for the wall construction. Please consult your dealer, custom installer or a building

contractor in this situation.

• Do not use the keyhole mounting bracket for ceiling installations! Please consult your dealer,

custom installer or a building contractor in this situation.

SPEAKER WIRE CONNECTIONS

Switch your electronics OFF when making all connections! When making any type of speaker wire

connection, be sure to observe proper polarity (+ to + and - to -). Most speaker wire is insulated, two

conductor, stranded construction and is color-coded or has some distinguishing feature differentiating

the two conductors. Speaker wire connectors on most loudspeakers and ampliﬁers are also color-

coded. Typically, RED is positive (+) and BLACK is negative (-), or ground. It does not matter which

conductor is connected to the positive or negative terminals of your equipment as long as you are

consistent. Be sure that the connections from all of the ampliﬁer channels to all of the speakers in

your system are connected in a like manner. If not, the quantity of bass will be reduced and the stereo

image will be compromised. Be careful to avoid excess bare wire or loose strands of wire at the con-

nections. This could cause a short between adjacent positive and negative terminals, damaging your

ampliﬁer. Eighteen gauge (AWG) wire is the minimum size recommended for short distances with

larger gauges recommended for longer runs. Consult your Klipsch dealer for speciﬁc suggestions.

Connect the SB-1 to the “Front” or “Main” channel speaker outputs of your system’s power ampliﬁer.

Connect the SC.5 to the “Center” channel speaker output of your system’s power ampliﬁer.

Connect the SS.5 to the “Rear” or “Surround” channel speaker outputs of your system’s power

ampliﬁer. When connecting surround speakers to the rear channels of a 5.1 channel system, it is

important that they are hooked up to the appropriate left and right rear channels as the surround

effects are in stereo.

BASS MANAGEMENT

Most surround sound electronics are equipped with a bass management system that permits the selec-

tion of a full- or limited-range (bass ﬁltered) operation for each speaker. You will normally conﬁgure

the main channels of your surround processor for the “Large” or “Full Range” setting. This will pro-

vide a full range signal to the SB-1s when used without an optional subwoofer. If a powered sub-

woofer is connected to the systems main channels, the “Large” setting will again be selected. Some

subwoofers provide bass ﬁltering for your main speakers when they are connected directly to the sub-

woofer. This type of hookup can reduce distortion and increase the dynamic capabilities of your

main speakers. If the subwoofer is connected to a line level subwoofer output on your electronics,

you can ﬁlter the bass signals from your main speakers by selecting the “Small” or “Limited Range”

setting for the main channels. Set the center and surround channels to the “Small” or “Limited

Range” setting. Consult your Klipsch dealer for more speciﬁcs on the bass management conﬁguration

of your electronics.

Missbrauch melden von Frage und/oder Antwort

Libble nimmt den Missbrauch seiner Dienste sehr ernst. Wir setzen uns dafür ein, derartige Missbrauchsfälle gemäß den Gesetzen Ihres Heimatlandes zu behandeln. Wenn Sie eine Meldung übermitteln, überprüfen wir Ihre Informationen und ergreifen entsprechende Maßnahmen. Wir melden uns nur dann wieder bei Ihnen, wenn wir weitere Einzelheiten wissen müssen oder weitere Informationen für Sie haben.

Klipsch SS-5 Seite 8

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Missbrauch melden von Frage und/oder Antwort

Art des Missbrauchs:

Forenregeln

Neu registrieren

Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Ihre Frage wurde zu diesem Forum hinzugefügt

Info