Bedienungsanleitung Klipsch SWS (Seite 6 von 12) (Englisch)

588374

Zoom out

Zoom in

Vorherige Seite

1/12

Nächste Seite

When the SWS is connected to a

Klipsch ProMedia speaker with the

SWS link output jack, to a TV set with

variable-level audio output jacks, or to

a home audio system, the volume-con-

trol module is used only to adjust the

balance of bass from the SWS to high-

er sounds from the other speakers (see

“Placement and Setup”). The volume

control on your ProMedia speaker sys-

tem, TV set, or audio system will func-

tion as a master volume control for the

entire system.

Multiple Subwoofers

It is easy to daisy-chain multiple SWS

subwoofers for higher performance

and output capability, using the SWS-

link, loop-through RCA input and out-

put jacks on the back of each SWS.

Just connect the included audio inter-

connect cable with RCA (phono) plugs

on each end from the RCA OUTPUT

jack on the back of the first SWS to

the RCA INPUT jack on the back of the

second. To add another, connect the

OUTPUT on the second subwoofer to

the INPUT on the third, and so on. The

volume-control module connected to

the first SWS in the chain adjusts the

level for all.

Placement and Setup

Because the SWS reproduces only very

low frequencies, you can place it

almost anywhere with good results. In

most cases, however, you will get best

performance with it placed in a corner.

If that’s not practical, try to start out

with it against a wall, since proximity

to room boundaries strengthens low-

frequency output. Bass response will

vary according to the position of a

subwoofer in the room, so you may

want to experiment with different

placements until you get the result you

find most pleasing.

Once you have completed all signal

connections and chosen an initial loca-

tion for the SWS, you’re ready to plug

it into a wall outlet and restore power

to the rest of the system. Then you can

make your final adjustments.

Volume Control Connection

(Fig. 5)

The SWS comes with an

external remote volume-

control module for

adjusting subwoofer level.

You can place it wherever is

convenient. Just run the cable from it

back to the SWS and plug it into the

back-panel minijack labeled VOLUME.

In the passthrough configuration used

with most multimedia speaker systems,

the volume controls on the SWS and

your main speakers are independent.

That is, changing the volume on one

does not affect the volume on the

other. So if you change the volume set-

ting on the main speakers, you must

readjust the SWS volume control as

well in order to maintain the same

tonal balance. For this reason, it is

usually more convenient to use the

SWS volume control only to adjust the

balance between it and the main

speakers and not to use the volume

control on the main speakers at all

once you have completed initial setup.

Instead, use the software volume con-

trol in your computer’s operating sys-

tem as the master volume control.

Figure 5

Missbrauch melden von Frage und/oder Antwort

Libble nimmt den Missbrauch seiner Dienste sehr ernst. Wir setzen uns dafür ein, derartige Missbrauchsfälle gemäß den Gesetzen Ihres Heimatlandes zu behandeln. Wenn Sie eine Meldung übermitteln, überprüfen wir Ihre Informationen und ergreifen entsprechende Maßnahmen. Wir melden uns nur dann wieder bei Ihnen, wenn wir weitere Einzelheiten wissen müssen oder weitere Informationen für Sie haben.

Klipsch SWS Seite 6

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Missbrauch melden von Frage und/oder Antwort

Art des Missbrauchs:

Forenregeln

Neu registrieren

Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Ihre Frage wurde zu diesem Forum hinzugefügt

Info