Bedienungsanleitung Koenic KDW 60031 A2 FI (Seite 25 von 34) (Deutsch, Englisch)

782789

Zoom out

Zoom in

Vorherige Seite

1/34

Nächste Seite

English

Preparation

Putting salt into the salt container

Fig. 2Depending on your tap water hardness

(hardness degree) use additional salt

(water softener). Always consider

instruction provided with the salt.

• Remove the basket and then

unscrew and remove the cap from

the salt container.

• Before ﬁrst usage, pour 1.5 lt. of

water in the salt container of your

machine.

• Place the end of the funnel

(supplied) into the hole and pour in

about 1.5 kg of salt. It is normal for a

small amount of water to come out

of the salt container.

• After ﬁlling the container, screw the

cap tight by turning it clockwise.

• Immediately after ﬁlling the salt

into the salt container, a washing

program should be started (rapid

program suggested). Otherwise

the ﬁlter system, pump or other

important parts of the machine may

be damaged by salty water which

will void the warranty.

• If the salt container is empty, the

softener (salt) indicator light

turns on.

Note:

Depending on how fast/fully the salt

dissolves, the salt warning light may still be

on even though the salt container is ﬁlled.

Warning

• Only use salt speciﬁcally designed for

use in dishwashers! All other types of

salt, not speciﬁcally designed for use

in a dishwasher, especially table salt,

will damage the dishwasher. In case of

damages caused by the use of unsuitable

salt the manufacturer does not give any

warranty nor is liable for any caused

damages.

• If salt has been spilled, a soak or a rapid

program should be run to remove the

excess salt.

• Only ﬁll in salt right before starting one

of the complete washing programs. This

will prevent any grains of salt or salty

water, which may have been spilled, from

remaining on the bottom of the machine

for any period of time, which may cause

corrosion.

• The salt container must only be reﬁlled

when the salt warning light in the control

panel comes on.

Adjusting salt consumption

Fig. 3Activate the setup mode: Switch

on the dishwasher with the on/o

switch and push and hold the program

buttonP for approx. 6 seconds. The

machine will enter the setting mode

which is indicated by the alternatingly

blinking indicator lights of and .

Adjust level of salt consumption:

Press the program button P to select

the proper setting according to your

local environment. Follow the table

below to ﬁnd correct setting.

Water Hardness level Setting

°dH 1) mmol/l 2)

0-5 0-0.94 H1

6-11 1.0-2.0 H2

12-17 2.1-3.0 H3*

18-22 3.1-4.0 H4

23-34 4.1-6.0 H5

35-55 6.1-9.8 H6

The product will exit the setup mode

automatically 5 seconds after the last

setting/operation of the switch.

Note:

1) German measurement for the degree of

water hardness

2) Millimol, international unit for water hardness

*) Factory setting

Contact your local water board for

information on the hardness of your water

supply.

IM_KDW 60031 A2 FI_180326_V05_HR.indb 25 26/3/18 12:08 pm

Missbrauch melden von Frage und/oder Antwort

Libble nimmt den Missbrauch seiner Dienste sehr ernst. Wir setzen uns dafür ein, derartige Missbrauchsfälle gemäß den Gesetzen Ihres Heimatlandes zu behandeln. Wenn Sie eine Meldung übermitteln, überprüfen wir Ihre Informationen und ergreifen entsprechende Maßnahmen. Wir melden uns nur dann wieder bei Ihnen, wenn wir weitere Einzelheiten wissen müssen oder weitere Informationen für Sie haben.

Koenic KDW 60031 A2 FI Seite 25

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Missbrauch melden von Frage und/oder Antwort

Art des Missbrauchs:

Forenregeln

Neu registrieren

Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Ihre Frage wurde zu diesem Forum hinzugefügt

Info