Bedienungsanleitung Koenic KFZ 511 E NF (Seite 21 von 145) (Deutsch, Englisch, Holländisch, Französisch, Italienisch, Portugiesisch, Spanisch, Polnisch, Türkisch, Schwedisch)

782829

Zoom out

Zoom in

Vorherige Seite

1/145

Nächste Seite

English

Adjust the side of the hinges

Attention

Make sure that the freezer stands savely and

cannot tilt.

Note:

• If necessary, or if the premises require it,

the mounting of the doors can be changed.

To do this, follow below instructions in the

given order.

• The following tools are required:

Socket wrench 8 mm, wrench 8mm, phillips

screwdriver, slotted screwdriver. Due to

the uniqueness of the appropriate tools,

those are not mentioned separately in the

following instructions.

• For this work a dierent hinge holder and

cover are needed, which are provided with

the unit.

Caution

• Pull out the mains plug!

• The mounting should be performed by at

least 2 persons to avoid dangers.

1 Pull o the top cover. If necessary use a

plastic card or spatula to loosen the cap.

2 Disconnect the plugs and sockets.

3 During unscrewing hold the refrigerator door

or it might be damaged. Remove the three

screws of the top hinge.

4 Pull out the door and place it on a soft and

clean surface.

5 Remove the blind cap on the top of the

freezer (use a plastic card or spatula to help

loosen the cap) and insert it into the holes

on the right side.

6 Pull o the decorative strip at the top of the

door and place the cable to the other side as

shown.

7 Make sure the cable is placed correctly and

clip the decorative strip back to the upper

side of the door.

8 Remove the hinge part with the door stop

at the bottom of the door. Take the supplied

new hinge part with door stop and ﬁx it to

the other side of the door. Make sure that

the hinge part is correctly seated in the

designated recess.

9 Loosen the two screws on the lower hinge

plate and remove them. If necessary tilt

the refrigerator to get better access to the

bottom side.

Unscrew the hinge pin and foot and re-

attach them on the opposite side.

Remove the two caps and the screw on the

left side. Attach the screw and caps on the

right side.

Position the hinge plate on the left side so

that holes and tapped holes are aligned.

Tighten the hinge plate properly.

Place the door on the lower hinge pin.

Keep the door in position. Take the

additional upper hinge provided and insert

the hinge pin into the corresponding hole in

the upper side of the door. Hold the hinge

plate in position and screw it on.

Remove the switch from the right-hand cap

and insert it into the supplied left-hand cap.

Connect the plugs and sockets. With the

door open, attach the supplied left cover

cap to the hinge so that it snaps into place

at all corners and edges, and ﬁx it to the

refrigerator with the screw. Make sure that

you do not damage the cables.

Missbrauch melden von Frage und/oder Antwort

Libble nimmt den Missbrauch seiner Dienste sehr ernst. Wir setzen uns dafür ein, derartige Missbrauchsfälle gemäß den Gesetzen Ihres Heimatlandes zu behandeln. Wenn Sie eine Meldung übermitteln, überprüfen wir Ihre Informationen und ergreifen entsprechende Maßnahmen. Wir melden uns nur dann wieder bei Ihnen, wenn wir weitere Einzelheiten wissen müssen oder weitere Informationen für Sie haben.

Koenic KFZ 511 E NF Seite 21

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Missbrauch melden von Frage und/oder Antwort

Art des Missbrauchs:

Forenregeln

Neu registrieren

Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Ihre Frage wurde zu diesem Forum hinzugefügt

Info