Bedienungsanleitung Koenic KWDR 8632 B INV (Seite 28 von 39) (Deutsch, Englisch)

782842

Zoom out

Zoom in

Vorherige Seite

1/39

Nächste Seite

English

Installation

Note:

The washer-dryer is equipped with power

cord and plug and needs sewage and

tap water connections. Make sure before

installation that a suitable wall outlet,

sewage and tap water connection are

available at the desired place of installation.

Consider the dimensions (chapter Technical

data) of the product for placing and

installation.

Caution

• Before initial operation the transport

restraints must be removed from the

backside of the unit. Operating the

washer-dryer with mounted transport

restraints leads to serious damages.

• Keep the transport restraints for later

use. Never transport the device without

correctly mounted transport restraints!

Fig. 1Loosen the four transport restraints

with a wrench (13 mm) and unscrew

them completely. Then insert the 4

supplied blind plugs in the holes.

Fig. 2Place the appliance on an even,

horizontal and steady surface. For

levelling the feet are adjustable and can

be screwed in or out.

• Unscrew the lock nuts with an open-

end wrench (17 mm).

• Turn the feet to the right to screw

them in and to the left to unscrew

them.

• Use a spirit level to check

whether the appliance is leveled.

If the appliance is not standing

horizontally or is tilting the feet

must be adjusted again.

• If the unit is leveled and does not

tilt, tighten the lock nuts with the

open-end wrench.

Note:

Note the following, when placing the

appliance on a platform:

The appliance might move during spinning

and could fall of a platform. To prevent this,

the feet must be secured with retaining tabs

(available in specialized stores).

Fig. 3The washer-dryer must be connected

to a drain.

• The drain hose is already ﬁxed to the

sewage connection. Pull the hose

out of the clamps and unwind it.

• Connect the other end to the

drainpipe (Option B, hose end at

least 60cm high) or place the end

of the hose in a sink or washbasin

(Option A, end of hose at a maximum

height of 100cm).

Note:

Suitable hose holders are available as

optional accessories.

Fig. 4Connect the water inlet to the water

system (3/4“) using the supplied hose

and make sure that everything is

connected correctly and ﬁrmly. The

water pressure must be between

0.05MPa and 1 MPa. A pressure

reducing valve must be used if the

water pressure is exceeds 1 MPa.

Note:

• If the water pipes are new or have not

been used for an extended period of time,

allow a certain amount of water to drain

until you are sure that the water is clear

and free of foreign objects.

• If this point is not observed, there is a risk

that the water inlet will become clogged

and the unit will be damaged.

• The sewage and tap water connection

must be checked on a regular basis.

Fig. 5Plug the mains plug into a suitable

socket.

IM_KWDR 8632 B INV_211029_V08_HR.indb 28IM_KWDR 8632 B INV_211029_V08_HR.indb 28 29/10/2021 10:10 AM29/10/2021 10:10 AM

Missbrauch melden von Frage und/oder Antwort

Libble nimmt den Missbrauch seiner Dienste sehr ernst. Wir setzen uns dafür ein, derartige Missbrauchsfälle gemäß den Gesetzen Ihres Heimatlandes zu behandeln. Wenn Sie eine Meldung übermitteln, überprüfen wir Ihre Informationen und ergreifen entsprechende Maßnahmen. Wir melden uns nur dann wieder bei Ihnen, wenn wir weitere Einzelheiten wissen müssen oder weitere Informationen für Sie haben.

Koenic KWDR 8632 B INV Seite 28

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Missbrauch melden von Frage und/oder Antwort

Art des Missbrauchs:

Forenregeln

Neu registrieren

Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Ihre Frage wurde zu diesem Forum hinzugefügt

Info