Bedienungsanleitung Koenic KWM 6212 D (Seite 22 von 32) (Deutsch, Englisch)

782847

Zoom out

Zoom in

Vorherige Seite

1/32

Nächste Seite

English

Installation

Note:

The washing machine is equipped with

power cord and plug and needs sewage and

tap water connections. Before installation,

make sure that suitable connections are at

the desired place of installation.

Consider the dimensions (chapter Technical

data) of the product for placing and

installation.

Caution

• Before initial operation the transport

restraints must be removed from the

backside of the unit. Operating the

washing machine with mounted transport

restraints leads to serious damages.

• Keep the transport restraints for later

use. Never transport the device without

correctly mounted transport restraints!

Fig. 1Loosen the four transport restraints

with a wrench (13 mm) and unscrew

them completely. Insert the 4 supplied

blind plugs in the holes.

Fig. 2Place the washing machine on an even,

horizontal and steady surface. For

levelling, the feet are adjustable and can

be screwed in or out.

• If the feet cannot be loosened by

hand, use pliers.

• Turn the feet to the right to screw

them in and to the left to unscrew

them.

• Use a spirit level to check whether

the appliance is levelled. If the

appliance is not standing horizontally

or is tilted, the feet must be adjusted

again.

• If the unit is levelled and does not

tilt, tighten the nuts with an open-

end wrench.

Note:

Note the following, when placing the

appliance on a platform:

The appliance might move during spinning

and could fall of a platform. To prevent this,

the feet must be secured with retaining tabs

(available in specialized stores).

Fig. 3The washing machine must be

connected to a drain.

• The drain hose is already ﬁxed to the

sewage connection. Pull the hose out

of the clamps and unwind it.

• Connect the other end to the drain

pipe (option A or B). Observe the max.

height of the hose end.

Note:

• To avoid leakage, a hose clamp should be

used to correctly install the outlet hose.

• Suitable hose holders are available as

optional accessories.

Fig. 4Connect the water inlet to the water

system (3/4“) using the supplied hose

and make sure that everything is

connected correctly and ﬁrmly. The

water pressure must be between

0.05MPa and 1 MPa. A pressure

reducing valve must be used if the

water pressure exceeds 1 MPa. The

correct installation of the water

connection should be checked on a

regular basis.

Note:

• If the water pipes are new or have not

been used for an extended period of time,

allow a certain amount of water to drain

until you are sure that the water is clear

and free of foreign objects.

• If this point is not observed, there is a risk

that the water inlet will become clogged

and the unit will be damaged.

Fig. 5Plug the mains plug into a suitable

socket.

IM_KWM6212 D_DE_EN_201126_V05_HR.indb 22IM_KWM6212 D_DE_EN_201126_V05_HR.indb 22 26/11/2020 10:53 AM26/11/2020 10:53 AM

Missbrauch melden von Frage und/oder Antwort

Libble nimmt den Missbrauch seiner Dienste sehr ernst. Wir setzen uns dafür ein, derartige Missbrauchsfälle gemäß den Gesetzen Ihres Heimatlandes zu behandeln. Wenn Sie eine Meldung übermitteln, überprüfen wir Ihre Informationen und ergreifen entsprechende Maßnahmen. Wir melden uns nur dann wieder bei Ihnen, wenn wir weitere Einzelheiten wissen müssen oder weitere Informationen für Sie haben.

Koenic KWM 6212 D Seite 22

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Missbrauch melden von Frage und/oder Antwort

Art des Missbrauchs:

Forenregeln

Neu registrieren

Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Ihre Frage wurde zu diesem Forum hinzugefügt

Info