Bedienungsanleitung Koga Pace B20 - 2022 (Seite 98 von 148) (Deutsch, Englisch, Holländisch, Dänisch, Französisch)

799481

Zoom out

Zoom in

Vorherige Seite

1/148

Nächste Seite

English – 2

0 275 007 XD2 | (25.04.2018) Bosch eBike Systems

Technical data

Drive unit Active Line Performance Line Performance

Line CX

Cruise Speed

Product code BDU250C

BDU255C

BDU250P BDU290P BDU250P CX

Continuous rated power W 250 250 250 250

Torque at drive, max. Nm 50 63 63 75

Rated voltage V = 36 36 36 36

Operating temperature °C -5 to +40 -5 to +40 -5 to +40 -5 to +40

Storage temperature °C -10 to +50 -10 to +50 -10 to +50 -10 to +50

Protection rating IP 54 (dust- and

splash-proof)

IP 54 (dust- and

splash-proof)

IP 54 (dust- and

splash-proof)

IP 54 (dust- and

splash-proof)

Weight, approx. kg 4 4 4 4

Bicycle lights A)

Voltage approx.B)C) V = 6/12

Maximum power

– Front light W 8.4/17.4

– Taillight W 0.6/0.6

A) Depends on legal regulations, not possible in all coun-

try-specific models via the eBike battery

B) The voltage level is preset and can only be changed by

the bicycle dealer.

C) When changing the bulbs, ensure that they are compat-

ible with the Bosch eBike system (ask your bicycle

dealer) and are suitable for the specified voltage. Bulbs

must only be replaced with bulbs of the same voltage.

Inserting a bulb incorrectly can cause it to blow.

Assembly

Inserting and removing the battery

For inserting and removing the eBike battery in/from the

eBike, please read and observe the battery operating in-

structions.

Checking the speed sensor (see figure A)

The speed sensor (2) and its spoke magnet (3) must be fit-

ted such that the spoke magnet moves past the speed

sensor at a distance of at least 5 mm and at most 17 mm

with each rotation of the wheel.

Note: If the distance between the speed sensor (2) and the

spoke magnet (3) is too small or too large, or if the speed

sensor (2) is not properly connected, the speedometer dis-

play will fail and the eBike drive unit will operate in emer-

gency mode.

Should this occur, loosen the screw of the spoke magnet (3)

and fasten the spoke magnet to the spoke such that it runs

past the marking on the speed sensor at the correct clear-

ance. If the speed is still not being indicated on the speedo-

meter display after doing this, please contact an authorised

bicycle dealer.

Operation

Start-up

Requirements

The eBike system can only be activated when the following

requirements are met:

– A sufficiently charged battery is inserted (see battery op-

erating instructions).

– The on-board computer is properly inserted in the holder

(see on-board computer operating instructions).

– The speed sensor is correctly connected (see "Checking

the speed sensor (see figure A)", pageEnglish–2).

Switching the eBike system on/off

The following options are available for switching on the

eBike system:

– If the on-board computer is already switched on when you

insert it into the holder, the eBike system will be switched

on automatically.

– When the on-board computer and the eBike battery are

inserted, briefly press the On/Off button of the on-board

computer.

– With the on-board computer inserted, push the On/Off

button on the eBike battery (bicycle manufacturer-spe-

Missbrauch melden von Frage und/oder Antwort

Libble nimmt den Missbrauch seiner Dienste sehr ernst. Wir setzen uns dafür ein, derartige Missbrauchsfälle gemäß den Gesetzen Ihres Heimatlandes zu behandeln. Wenn Sie eine Meldung übermitteln, überprüfen wir Ihre Informationen und ergreifen entsprechende Maßnahmen. Wir melden uns nur dann wieder bei Ihnen, wenn wir weitere Einzelheiten wissen müssen oder weitere Informationen für Sie haben.

Koga Pace B20 - 2022 Seite 98

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Missbrauch melden von Frage und/oder Antwort

Art des Missbrauchs:

Forenregeln

Neu registrieren

Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Ihre Frage wurde zu diesem Forum hinzugefügt

Info