Bedienungsanleitung Kona 2021 (Seite 14 von 46) (Englisch)

780520

Zoom out

Zoom in

Vorherige Seite

1/46

Nächste Seite

KONA OWNER’S MANUAL

1. Up and down adjustment.

To check for correct saddle

height [Fig. 3]:

• sit on the saddle;

• place one heel on a pedal;

• rotate the crank until the

pedal with your heel on it is

in the down position and the

crank arm is parallel to the

seat tube.

If your leg is not completely

straight and just touching the

center of the pedal, your saddle height needs to be adjusted.

If your hips must rock for the heel to reach the pedal, the

saddle is too high. If your leg is bent at the knee with your

heel on the pedal, the saddle is too low.

Ask your dealer to set the saddle for your optimal riding

position and to show you how to make this adjustment.

If you choose to make your own saddle height adjustment:

- loosen the seat post clamp

- raise or lower the seat post in the seat

tube

- make sure the saddle is straight fore

and aft

- re-tighten the seat post clamp to

the recommended torque (see the

manufacturer's instructions).

Once the saddle is at the correct

height, make sure that the seatpost

does not project from the frame

beyond its “Minimum Insertion” or

“Maximum Extension” mark [Fig. 4].

WARNING: If your seat post is not inserted in the

seat tube as described in B.1 above, the seat post,

binder or even frame may break, which could cause

you to lose control and fall.

2. Front and back adjustment. The saddle can be adjusted

forward or back to help you get the optimal position

on the bike. Ask your dealer to set the saddle for your

optimal riding position and to show you how to make this

adjustment. If you choose to make your own front and

back adjustment, make sure that the clamp mechanism

is clamping on the straight part of the saddle rails and is

not touching the curved part of the rails, and that you are

using the recommended torque on the clamping fastener(s)

(see the manufacturer’s instructions).

3. Saddle angle adjustment. Most people prefer a horizon-

tal saddle; but some riders like the saddle nose angled up

or down just a little. Your dealer can adjust saddle angle or

teach you how to do it. If you choose to make your own

saddle angle adjustment and you have a single bolt sad-

dle clamp on your seat post, it is critical that you loosen

the clamp bolt sufciently to allow any serrations on the

mechanism to disengage before changing the saddle’s

angle, and then that the serrations fully re-engage before

you tighten the clamp bolt to the recommended torque

(see the manufacturer’s instructions).

WARNING: When making saddle angle adjustments

with a single bolt saddle clamp, always check to

make sure that the serrations on the mating surfaces

of the clamp are not worn. Worn serrations on the

clamp can allow the saddle to move, causing you to

lose control and fall. Always tighten fasteners to the

correct torque. Bolts that are too tight can stretch and

deform. Bolts that are too loose can move and fatigue.

Missbrauch melden von Frage und/oder Antwort

Libble nimmt den Missbrauch seiner Dienste sehr ernst. Wir setzen uns dafür ein, derartige Missbrauchsfälle gemäß den Gesetzen Ihres Heimatlandes zu behandeln. Wenn Sie eine Meldung übermitteln, überprüfen wir Ihre Informationen und ergreifen entsprechende Maßnahmen. Wir melden uns nur dann wieder bei Ihnen, wenn wir weitere Einzelheiten wissen müssen oder weitere Informationen für Sie haben.

Kona 2021 Seite 14

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Missbrauch melden von Frage und/oder Antwort

Art des Missbrauchs:

Forenregeln

Neu registrieren

Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Ihre Frage wurde zu diesem Forum hinzugefügt

Info