Bedienungsanleitung Konig CMP-WNROUT20 (Seite 6 von 75) (Deutsch, Englisch, Holländisch, Französisch, Italienisch, Spanisch, Schwedisch, Finnisch)

533078

Zoom out

Zoom in

Vorherige Seite

1/75

Nächste Seite

6.4 WDS Settings

WDS (Wireless Distribution System) is used to expand wireless coverage area. This router provides three modes: Lazy,

Bridge and Repeater.

Lazy: In this mode, the connected device can be Bridge mode or Repeater mode and enter the router’s BSSID to

establish the connection.

Bridge: You can wirelessly connect two or more wired networks via this mode. In this mode, you need to add the Wireless

MAC address of the connecting device into the router’s AP MAC address table or select one from the scanning table.

Repeater Mode: In this mode, add the opposing MAC address into each own AP MAC address table manually or by

scanner to enlarge and extend the wireless radio.

Chapter 7: DHCP Server

7.1 DHCP Settings

DHCP (Dynamic Host Control Protocol) is to assign an IP address to the computers on the LAN/private network. When

you enable the DHCP Server, the DHCP Server will allocate automatically an unused IP address from the IP address pool

to the requesting computer in premise of activating “Obtain an IP Address Automatically”. So specifying the starting and

ending address of the IP Address pool is needed.

•

DHCP Server: Activate the checkbox to enable DHCP server.

•

IP Address Start/End: Enter the range of IP addresses for DHCP server distribution.

•

Lease Time: The length of the IP address lease.

Chapter 8: Upgrade Firmware

8.1 The Router provides the firmware upgrade by clicking “Upgrade” after browsing the firmware upgrade packet,

which you can download from www.nedis.nl

•

Browse: Click this button to select the upgrade file.

•

Upgrade: Click this button to start the upgrading process. After the upgrade is completed, the router will reboot

automatically.

8.2 Reboot the Router

Rebooting the Router makes the settings congured go into effect or to set the router again if setting failure occurs.

8.3 Password Change

This section is to set a new user name and password to better secure your router and network.

•

User Name: Enter a new user name for the device.

•

Old Password: Enter the old password.

•

New Password: Enter a new password.

•

Re-enter to Confirm: Re-enter to confirm the new password.

8.4 Logout

After you have nished the settings completely, in logout page click “Yes” to logout the web management page.

How to install and set-up a router on a cable or ADSL modem

Caution!

Follow these steps without skipping a step

1. Switch the modem off (disconnect from mains power).

2. Switch the PC/laptop off.

3. Connect the LAN output of the modem via LAN cable to the blue port of the router.

4. Connect one of the yellow ports via LAN cable to the PC/laptop.

5. Now switch on the modem and wait until it is fully logged in (this can take a moment).

6. Switch on the router and wait at least 30 seconds.

Missbrauch melden von Frage und/oder Antwort

Libble nimmt den Missbrauch seiner Dienste sehr ernst. Wir setzen uns dafür ein, derartige Missbrauchsfälle gemäß den Gesetzen Ihres Heimatlandes zu behandeln. Wenn Sie eine Meldung übermitteln, überprüfen wir Ihre Informationen und ergreifen entsprechende Maßnahmen. Wir melden uns nur dann wieder bei Ihnen, wenn wir weitere Einzelheiten wissen müssen oder weitere Informationen für Sie haben.

Konig CMP-WNROUT20 Seite 6

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Missbrauch melden von Frage und/oder Antwort

Art des Missbrauchs:

Forenregeln

Neu registrieren

Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Ihre Frage wurde zu diesem Forum hinzugefügt

Info