Bedienungsanleitung Konig Electronic KN-STUDIO91 (Seite 3 von 32) (Deutsch, Englisch, Holländisch, Dänisch, Französisch, Italienisch, Spanisch, Schwedisch, Norwegisch, Finnisch)

570558

Zoom out

Zoom in

Vorherige Seite

1/32

Nächste Seite

Synchronization

- Test button: For testing, or multiple flashes can be used.

- Sync socket: The standard 0.35 cm jack type socket on the rear panel of the unit may be used for direct

connection to a camera set to “x” synchronization. A “Radio remote control receiver” may also be plugged

into this socket.

- Photocell: The unit has a built-in photocell, enabling the unit to be triggered by the flash from any other

flash unit, or a small camera mounted flashgun. The photocell is mounted behind the red “Ready”

indicator on the rear panel.

Modeling lamp control

Set the yellow switch to “ ” to turn on the modeling lamp and keep it on all the time.

Fuse

The modeling and flash circuitry is protected by a single 7 amp fuse mounted on the rear panel. Never replace

the fuse with one of a different rating. Be sure to switch OFF the unit before changing the bulb or fuse.

Warning - high voltage

Do not touch the flashtube assembly for thirty minutes after disconnecting from the supply.

Safety precautions:

To reduce risk of electric shock, this product should ONLY be

opened by an authorized technician when service is required.

Disconnect the product from mains and other equipment if a

problem should occur. Do not expose the product to water or

moisture.

Maintenance:

Clean only with a dry cloth. Do not use cleaning solvents or abrasives.

Warranty:

No guarantee or liability can be accepted for any changes and modifications of the product or damage caused

due to incorrect use of this product.

General:

- Designs and specifications are subject to change without notice.

- All logos brands and product names are trademarks or registered trademarks of their respective holders

and are hereby recognized as such.

- This manual was produced with care. However, no rights can be derived. König Electronic can not accept

liability for any errors in this manual or their consequences.

- Keep this manual and packaging for future reference.

Attention:

This product is marked with this symbol. It means that used electrical and electronic products should

not be mixed with general household waste. There is a separate collections system for these products.

This product has been manufactured and supplied in compliance with all relevant regulations and directives,

valid for all member states of the European Union. It also complies with all applicable specifications and

regulations in the country of sales.

Formal documentation is available upon request. This includes, but is not limited to: Declaration of Conformity

(and product identity), Material Safety Data Sheet and product test report.

Please contact our customer service desk for support:

via website: http://www.nedis.com/en-us/contact/contact-form.htm

via e-mail: service@nedis.com

via telephone: +31 (0)73-5993965 (during office hours)

NEDIS B.V., De Tweeling 28, 5215 MC ’s-Hertogenbosch, THE NETHERLANDS

Missbrauch melden von Frage und/oder Antwort

Libble nimmt den Missbrauch seiner Dienste sehr ernst. Wir setzen uns dafür ein, derartige Missbrauchsfälle gemäß den Gesetzen Ihres Heimatlandes zu behandeln. Wenn Sie eine Meldung übermitteln, überprüfen wir Ihre Informationen und ergreifen entsprechende Maßnahmen. Wir melden uns nur dann wieder bei Ihnen, wenn wir weitere Einzelheiten wissen müssen oder weitere Informationen für Sie haben.

Konig Electronic KN-STUDIO91 Seite 3

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Missbrauch melden von Frage und/oder Antwort

Art des Missbrauchs:

Forenregeln

Neu registrieren

Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Ihre Frage wurde zu diesem Forum hinzugefügt

Info