731315
8
Zoom out
Zoom in
Vorherige Seite
1/276
Nächste Seite
ENGLISH
8
Note:
1) The alarm unit will give a conformation tone when armed or disarmed. The
tone for CHIME is dierent as for ALARM.
2) If a sensor does not need to be switched on, it’s possible to switch o every
sensor individually with the on/o switch. In this case the sensor is no part
of the alarm system anymore when armed (except PIR sensor).
3) A sensor switched to RF+ALARM will always give an alarm sound on the
sensor itself, unless the alarm unit is armed or disarmed.
4) When a sensor is triggered and the siren of the alarm unit sounds, it needs
to be switched o with on/o switch of the alarm unit. After that the alarm
unit can be switched on again. When the alarm keeps on going after arming
the system, check if every sensor is installed properly.
Installation SAS-ALARM120
1. Insert, according the diagram inside the battery compartment, (backside)
the batteries for the alarm unit (3x AA).
2. Install the door/window sensor with the adhesive tape to doors and
windows. Note: maximum 1cm distance between magnetic contact and
sensor (see gure 2). Switch on the sensor to RF or RF+ALARM. If switched
to RF+ALARM, the sensor will send, when triggered, a signal to the alarm
unit and the siren of the sensor itself will also sound. In this case the siren of
the sensor and the alarm unit will both sound.
3. Insert, according the diagram inside the battery compartment, (backside)
the batteries for PIR sensor (3x AAA). The PIR sensor needs to warm up for
30~40seconds for rst use. In this period it cannot detect motion. Install
the PIR sensor at a height of 1~1.5m for best performance. Do not install
the PIR sensor into direct sunlight, facing towards windows, objects that
move easily and heat or cold source.
4. Remove the transparent front cover of the alarm unit to write down the
position of the sensors corresponding with the numbered LED. (e.g. sensor
1=front door, 2=kitchen window, etc.).
5. Install the alarm unit to a location. The distance between the alarm unit and
the most far away sensor may not exceed 60m (open area)*.
6. Switch on the alarm unit to ALARM or CHIME function. If switched to
CHIME, the alarm unit will sound like a door bell when a door or window is
opened. Switched to ALARM generates a 100dB loud siren. When the alarm
unit is switched on, the alarm is not armed (active) yet. Push the ON button
8

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Forenregeln

Missbrauch melden von Frage und/oder Antwort

Libble nimmt den Missbrauch seiner Dienste sehr ernst. Wir setzen uns dafür ein, derartige Missbrauchsfälle gemäß den Gesetzen Ihres Heimatlandes zu behandeln. Wenn Sie eine Meldung übermitteln, überprüfen wir Ihre Informationen und ergreifen entsprechende Maßnahmen. Wir melden uns nur dann wieder bei Ihnen, wenn wir weitere Einzelheiten wissen müssen oder weitere Informationen für Sie haben.

Art des Missbrauchs:

Zum Beispiel antisemitische Inhalte, rassistische Inhalte oder Material, das zu einer Gewalttat führen könnte.

Beispielsweise eine Kreditkartennummer, persönliche Identifikationsnummer oder unveröffentlichte Privatadresse. Beachten Sie, dass E-Mail-Adressen und der vollständige Name nicht als private Informationen angesehen werden.

Forenregeln

Um zu sinnvolle Fragen zu kommen halten Sie sich bitte an folgende Spielregeln:

Neu registrieren

Registrieren auf E - Mails für Konig Electronic SAS-ALARM120 wenn:


Sie erhalten eine E-Mail, um sich für eine oder beide Optionen anzumelden.


Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Wenn Sie innerhalb von 15 Minuten keine E-Mail mit dem Handbuch erhalten haben, kann es sein, dass Sie eine falsche E-Mail-Adresse eingegeben haben oder dass Ihr ISP eine maximale Größe eingestellt hat, um E-Mails zu erhalten, die kleiner als die Größe des Handbuchs sind.

Ihre Frage wurde zu diesem Forum hinzugefügt

Möchten Sie eine E-Mail erhalten, wenn neue Antworten und Fragen veröffentlicht werden? Geben Sie bitte Ihre Email-Adresse ein.



Info