Bedienungsanleitung Konig KN-WS200 (Seite 3 von 56) (Deutsch, Englisch, Holländisch, Französisch, Italienisch, Spanisch, Schwedisch, Finnisch)

533096

Zoom out

Zoom in

Vorherige Seite

1/56

Nächste Seite

k. Under the RCC receiving mode, press “DOWN” key 2 seconds to exit the RCC receiving

mode.

3. Time setting:

a. Hold CLOCK 2 seconds, enter time setting mode.

b. Setting sequence is: Year → Month → Date → Language → Hour → Minute → exit

c. Push CLOCK key to conﬁ rm current setting and enter next setting

d. Click UP key, the setting will go ahead one step; Hold this key 2 seconds, the setting will run

forward by 8 steps/second.

e. Click DOWN key, the setting will backward for one step; Hold this key, the setting will run back

by 8 steps/second.

f. The system will exit automatically if no key is operated in 20 seconds.

4. Alarm setting:

a. Hold ALARM 2 seconds to enter alarm setting.

b. Setting sequence is : hour → minute → exit.

c. Click ALARM to conﬁ rm setting and enter next setting state.

d. Click UP key, the setting will go ahead one step; Hold this key 2 seconds, the setting will run

forward by 8 steps/second.

e. Click DOWN key, the setting will backward for one step; Hold this key, the setting will run back

by 8 steps/second.

f. The system will save the setting and exit automatically if no key is operated in 20 seconds.

D. Function and effect

1. RCC receiving function:

a. How to enter RCC receiving status.

I. It will into RCC receiving state automatically when power on or resetting.

II. It enters RCC receiving automatically at 2:00, 3:00, 4:00, 5:00 everyday.

b. RCC receiving time is 7 minutes.

c. It will receive radio signal automatically at 1:00-3:00 am, if it doesn‘t receive radio signal it will

start receiving at 4:00 and 5:00, if the signal has been received then the next RCC receiving

time is 1:00 am next day.

d. If can’t receive radio signal during 1:00 to 5:00, then next RCC receiving time is 1:00 next

day.

e. If the alarm rings during RCC receiving, system will exit RCC receiving and enter alarm

function.

f. When the DST signal is received, the DST symbol on the LCD will light, and the setting is

changed into daylight saving time.

g. If you change the time setting when the RCC symbol is lit, all the RCC symbols on the display

will be switched off.

2. Alarm function:

a. the BUZZER will ring for 2 seconds as below:

0 – 10 sec.: one “beep” per second

10 – 20 sec.: two “beeps” per second

20 – 30 sec.: four “beeps” per second

after 30 sec.: “beeps” continuously

b. When ringing, click SNZ/LIGHT key once to enter states 5 minutes snooze states, exit if any

other key is pushed.

3. System will stop temperature detection when RCC receiving or alarm ringing.

4. The indoor temperature display range: 0°C -- +50°C (32F -- +122F)

5. The indoor temperature proposed operating range: 0°C -- +40°C (32F -- +104F)

6. The indoor humidity range: 20% --- 95%

Missbrauch melden von Frage und/oder Antwort

Libble nimmt den Missbrauch seiner Dienste sehr ernst. Wir setzen uns dafür ein, derartige Missbrauchsfälle gemäß den Gesetzen Ihres Heimatlandes zu behandeln. Wenn Sie eine Meldung übermitteln, überprüfen wir Ihre Informationen und ergreifen entsprechende Maßnahmen. Wir melden uns nur dann wieder bei Ihnen, wenn wir weitere Einzelheiten wissen müssen oder weitere Informationen für Sie haben.

Konig KN-WS200 Seite 3

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Missbrauch melden von Frage und/oder Antwort

Art des Missbrauchs:

Forenregeln

Neu registrieren

Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Ihre Frage wurde zu diesem Forum hinzugefügt

Info