Bedienungsanleitung Konig KN-WS400 (Seite 3 von 48) (Deutsch, Englisch, Holländisch, Französisch, Italienisch, Spanisch, Schwedisch, Finnisch)

533098

Zoom out

Zoom in

Vorherige Seite

1/48

Nächste Seite

3.2 Normal states

1. Hold “Set” for 2 seconds to enter into time setting

2. Click “Alarm” to switch the alarm on/off

3. Hold “Alarm” for 2 seconds to enter into Alarm setting

4. Click “Up” to switch between 12 hr/24 hr

5. Press “Down” to switch between °C/°F

6. When ALARM rings, click “snooze” to enter into the snooze state every 5 minutes

7. Press “Channel” to switch RF channel, CH1 → CH2 → CH3

8. Hold “Channel” key for 2 seconds to clear out all data of current “Channel”

3.3 Time set

1. Hold “Set” key for 2 seconds to enter into time setting

2. The sequence of time setting: Year (2000-2050) → Month → Date → Language → Hour →

Minute → Time zone → Exit

3. There will have 1 Hz ﬂ ashing during setting

4. Press “Set” to conﬁ rm the setting, and enter the next setting state

5. Press “Up” one time, the setting will go ahead for one step; hold the key for 2 seconds, it will

run forward by 8 steps/second.

6. Press “Down” one time, the setting will backward for one step; hold for 2 seconds, it will run

back by 8 steps/second.

7. Moon phase is changed accordingly

8. The system will exit automatically if no key is operated in 8 seconds.

3.4 Alarm set

1. Hold “Alarm” key for 2 second to enter into alarm setting

2. The sequence of alarm setting: Hour → Minute → exit

3. There will have 1 Hz ﬂ ashing during setting

4. Press “Alarm” to conﬁ rm the setting, and enter the next setting state

5. Press “Up” one time, the setting will go ahead for one step; hold the keys for 2 seconds, it will

run forward by 8 steps/seconds.

6. Press “Down” one time, the setting will backward for one step; hold for 2 seconds, it will run

back by 8 steps/second.

7. The system will exit automatically if no key is operated in 8 seconds.

Function and effect

4.1 The receiving function of RF

1. After installing the battery and checking temperature/humidity, it will enter RF receiving state

automatically for 3 minutes.

2. Under normal display mode, hold the “Channel” key for 2 seconds to clear out the channel

information

3. If there is no effective signal with same ID code received for the current channel in 35 minutes,

the temperature of that CH will show “--. -“.

4. The temperature display will resume back when the correct signal is received again

4.2 The function of alarm

1. The BUZZER will ring for 2 seconds as below:

a. 0 – 10 sec.: one “beep” per second

b. 10 – 20 sec.: two “beeps” per second

c. 20 – 30 sec.: four “beeps” per second

d. After 30 sec.: “beeps” continuously

2. When the alarm goes off, click “Snooze” key once to enter states 5 minutes snooze states,

exit if any other key is clicked.

Missbrauch melden von Frage und/oder Antwort

Libble nimmt den Missbrauch seiner Dienste sehr ernst. Wir setzen uns dafür ein, derartige Missbrauchsfälle gemäß den Gesetzen Ihres Heimatlandes zu behandeln. Wenn Sie eine Meldung übermitteln, überprüfen wir Ihre Informationen und ergreifen entsprechende Maßnahmen. Wir melden uns nur dann wieder bei Ihnen, wenn wir weitere Einzelheiten wissen müssen oder weitere Informationen für Sie haben.

Konig KN-WS400 Seite 3

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Missbrauch melden von Frage und/oder Antwort

Art des Missbrauchs:

Forenregeln

Neu registrieren

Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Ihre Frage wurde zu diesem Forum hinzugefügt

Info