Bedienungsanleitung Konig KN-WS600 (Seite 3 von 125) (Deutsch, Englisch, Holländisch, Dänisch, Französisch, Italienisch, Spanisch, Schwedisch, Norwegisch, Finnisch)

533104

Zoom out

Zoom in

Vorherige Seite

1/125

Nächste Seite

2. Place the anemometer horizontally in your selected outdoor location. Loosen the screws on the battery

door with a small Phillips screwdriver and open the battery door. Insert 2 pieces of AA batteries according

to the polarity indicated. Close the battery door and tighten the screws.

3. Hold the “CHANNEL/SEARCH” button on the monitor for 3 seconds and the wind direction, temperature

and humidity icons will flash on the display. The monitor is now searching for all remote sensors.

4. If valid wind direction, wind speed and channel-1 temperature/humidity readings are shown on the monitor

within 10 minutes, the RF transmission is successful and the anemometer and monitor are within the

effective transmission range.

If the above readings are not shown after 10 minutes of searching, the transmission has failed.

Shorten the distance between the anemometers and monitor. Reset the anemometer by removing all

batteries from the anemometer and wait for 10 seconds before reinstalling the batteries. Repeat steps

3 and 4 until the transmission is successful.

5. Remove all batteries from the anemometer before mounting and calibration.

3. Mounting the anemometer

Important: Before mounting, make sure the monitor and anemometer are within the effective transmission

range.

Note: To mount the anemometer, you need a mast (not supplied) of about 1 – 1.25 inches (2.54 – 3.18 cm) in

diameter, and the hardware necessary to fasten it to the mounting location. If you have previously installed

such a mast (for a mounting antenna, for example), you can mount the anemometer on that mast.

(1) If necessary, mount and ground a mast as directed in the instructions provided by the mast.

(2) Place the supplied U-shaped metal plates around the mast. Insert 4 pieces of the supplied hex screws

through the holes of the U-shaped plates and the holes on the anemometer’s mounting bracket.

(The wind vane is above the wind cup and the metal bar of the anemometer is in the horizontal level).

(3) Tighten the supplied hex nut onto both ends of each screw.

4. Calibrating the anemometer and installing batteries

After mounting the anemometer, follow these steps to calibrate the wind direction so that the anemometer

properly measures the wind direction and transmits it to the monitor. Make sure the battery has been removed

from the anemometer before calibration.

Important: The same calibration (steps 1 to 5) is needed for the first setup and every battery replacement.

(1) After mounting the anemometer, loosen the screws on the battery door with a small screwdriver and

open the battery door.

(2) Use the compass on the anemometer and turn the wind vane so it is pointing due north.

(3) Hold the wind vane pointing due north and do not allow it to turn. Insert 2 pieces of AA batteries

according to the polarity indicated. The red LED indicator above the battery cover of the anemometer

MAST

NORTH

MAST

Missbrauch melden von Frage und/oder Antwort

Libble nimmt den Missbrauch seiner Dienste sehr ernst. Wir setzen uns dafür ein, derartige Missbrauchsfälle gemäß den Gesetzen Ihres Heimatlandes zu behandeln. Wenn Sie eine Meldung übermitteln, überprüfen wir Ihre Informationen und ergreifen entsprechende Maßnahmen. Wir melden uns nur dann wieder bei Ihnen, wenn wir weitere Einzelheiten wissen müssen oder weitere Informationen für Sie haben.

Konig KN-WS600 Seite 3

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Missbrauch melden von Frage und/oder Antwort

Art des Missbrauchs:

Forenregeln

Neu registrieren

Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Ihre Frage wurde zu diesem Forum hinzugefügt

Info