Bedienungsanleitung Korg AX1000G (Seite 13 von 23) (Englisch)

488490

Zoom out

Zoom in

Vorherige Seite

1/23

Nächste Seite

3. Editing

Setting the noise reduction and

program levels

1. If you are in Play mode, press the NR-LEVEL

switch.

2. By rotating value knobs 1 or 2, or pressing the NR-

LEVEL switch, you can access the screen displays

for adjusting the noise reduction and setting the

level for each program.

3. To adjust the amount of noise reduction, use value

knob 1 (range OFF...10: shown in the MASTER/

VALUE display).

4. To adjust the level of each program, use value knob

2 (range 0...10: shown in the MASTER/VALUE

display).

5. When you finish making settings, press the EXIT

switch to return to Play mode.

Level

Noise reduction

Instead of value knobs 1 and 2, you can also use the

cursor switches to select a parameter and use the

MASTER/VALUE switches (▲,▼) to adjust the value

of the parameter.

It is not possible to turn noise reduction off.

Depending on the guitar that you use, raising the noise

reduction setting too high may cause the sound to be cut

off at low levels.

The volume of each program will change depending on

the guitar that you use. Adjust the program level for your

guitar.

If you wish to save the noise reduction and program level

settings that you edited, you must perform the “Program

write” operation. If you turn off the power or select a

different program without writing the program, the

program you modified will revert to its previous settings.

Modifying program names

Press the RENAME switch and specify the desired

program name. Use the cursor switches ( , ) to

select the character that you wish to change (the

character will blink). Then use value knob 5 (or the

MASTER/VALUE switches) to select the desired

character. The available characters are shown below.

Available characters

Move between

character positions

Select characters

If you wish to save the modified program name, you must

perform the “Program write” operation. If you turn off the

power or select a different program without writing the

program, the program name you edited will revert to its

previous setting.

Writing programs

Here’s how to write an edited program.

1. Press the WRITE switch, and the name display will

indicate “✳WRITE✳.” The bank number display

and the program LED will blink.

2. Use the MASTER/VALUE switches (or value knob

5 and the bank switch) to select the writing

destination bank, and use the cursor switches (or

the program switch) to select the writing destina-

tion program.

3. Press the WRITE switch once again, and the display

will read “COMPLT” to indicate that the program

has been written. You will then return to Play

mode.

If you decide not to write, press the EXIT switch to

cancel the Write operation.

Select the bank Select the program

Select the bankSelect the program

If you write an edited program to a different program

number, the program that was overwritten will be lost.

It is not possible to write to a preset program.

Missbrauch melden von Frage und/oder Antwort

Libble nimmt den Missbrauch seiner Dienste sehr ernst. Wir setzen uns dafür ein, derartige Missbrauchsfälle gemäß den Gesetzen Ihres Heimatlandes zu behandeln. Wenn Sie eine Meldung übermitteln, überprüfen wir Ihre Informationen und ergreifen entsprechende Maßnahmen. Wir melden uns nur dann wieder bei Ihnen, wenn wir weitere Einzelheiten wissen müssen oder weitere Informationen für Sie haben.

Korg AX1000G Seite 13

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Missbrauch melden von Frage und/oder Antwort

Art des Missbrauchs:

Forenregeln

Neu registrieren

Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Ihre Frage wurde zu diesem Forum hinzugefügt

Info