Bedienungsanleitung Korg AX100G (Seite 6 von 18) (Englisch)

488491

Zoom out

Zoom in

Vorherige Seite

1/18

Nächste Seite

2. Playing the AX100G

Example display

Program mode

When you turn on the power, the AX100G will always enter Pro-

gram mode, and will be set to the program setting that were last

selected when the power was turned off.

Input level switch setting

Set this switch according to the output of your instrument.

H : Suitable for a pickup with a high output level, such as a

humbucking pickup

L : Suitable for a pickup with a low output level, such as a single

coil pickup

Adjusting the volume (master volume)

To adjust the volume, rotate the MASTER VOL. (master volume)

located on the rear panel.

Selecting a program

Press the UP or DOWN switches to increment or decrement the

programs in steps of one. When you do so, the multi-display

will show the name of each program.

Programs are organized into groups of four, and these groups

are called "banks." The current bank is shown by the 10's digit of

the number LED.

User program

Preset program

The AX100G contains a total of 80 programs (sounds): 40 (4 x 10

banks) of preset programs that cannot be overwritten, and 40 (4

x 10 banks) of user programs that you are able to modify (edit).

When a user program is selected, the decimal point (dot) in the

lower right of the number LED will light.

User

program

Preset

program

Dot is lit

Selecting a bank

Although you can use the UP or DOWN switches to select pro-

grams across banks, you can also switch programs by bank.

1. Press and hold the PROG/FX SELECT switch for approxi-

mately one second until the number LED begins to blink.

2. Press either the UP or DOWN switch to increment or decre-

ment the bank.

3. Press the PROG/FX SELECT switch once again to finalize the

bank and make the number LED stop blinking.

Bank Hold (10’s HOLD)

By simultaneously pressing the TAP switch and EXIT switch,

you can prevent programs of other banks from being selected.

At this time, the decimal point (dot) at the lower right of the 10's

place in the number LED will light.

Press the UP or DOWN switches to select programs within the

current bank.

When you once again press the TAP switch and EXIT switch

simultaneously, the Bank Hold (10’S HOLD) function will be can-

celled.

Dot is lit

Checking the effects used by a program

Some programs do not use all of the effects. When you select a

program, the LED beside each effect select switch will light to

indicate the effects that are being used. An effect that is turned

off can be edited (turned on) by pressing its select switch, and

when you press another select switch or the EXIT switch, the

LED will change from blinking to lit.

Bypass, Mute

By pressing the UP and DOWN switches simultaneously, you

can Bypass the AX100G so that no effects will be applied. (The

multi-display will indicate "BYPASS" for two second.)

Alternatively, by pressing the UP and DOWN switches simulta-

neously and holding them for approximately one second, you

can Mute the AX100G completely so that no sound will be out-

put. (The multi-display will indicate "MUTE" for two second.)

To defeat Bypass or Mute, press the UP or DOWN switch.

Auto tuner

When the AX100G is in bypass or mute condition, the tuner will

operate automatically. If you mute the AX100G you will be able

to tune your instrument without producing sound. This is used

for on stage tuning.

1. Tune your guitar so that the desired note

name appears in the number LED. The

decimal point “.” at the lower right of the

number LED will light to indicate a sharp



2. The seven-point pedal indicator will show the difference be-

tween the pitch you play and the note name. Tune your in-

strument so that only the center LED is lit.

Tuning discrepancy shown by the pedal indicator

and the multi-display

Correct

tuning

Pitch is

flat

Pitch is

sharp

Changing the calibration setting

As necessary, you can adjust the calibration (the frequency of the

standard A pitch) in the range of 438—445 Hz. (440 Hz is “stan-

dard”)

When the tuner is operating, you can rotate value knob 1 to ad-

just the calibration. The calibration setting is shown in the multi-

display.

When the power is turned off, the calibration setting you modify

will be lost, and will automatically return to 440 Hz the next

time the power is turned on.

Missbrauch melden von Frage und/oder Antwort

Libble nimmt den Missbrauch seiner Dienste sehr ernst. Wir setzen uns dafür ein, derartige Missbrauchsfälle gemäß den Gesetzen Ihres Heimatlandes zu behandeln. Wenn Sie eine Meldung übermitteln, überprüfen wir Ihre Informationen und ergreifen entsprechende Maßnahmen. Wir melden uns nur dann wieder bei Ihnen, wenn wir weitere Einzelheiten wissen müssen oder weitere Informationen für Sie haben.

Korg AX100G Seite 6

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Missbrauch melden von Frage und/oder Antwort

Art des Missbrauchs:

Forenregeln

Neu registrieren

Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Ihre Frage wurde zu diesem Forum hinzugefügt

Info