Bedienungsanleitung Korg Electribe ESX-1 (Seite 92 von 108) (Englisch)

488477

Zoom out

Zoom in

Vorherige Seite

1/108

Nächste Seite

Transmitting sound settings and

other data

Song, pattern, global, and MIDI settings can be transmit-

ted from the ESX-1 as MIDI exclusive data and stored on

an external device.

Transmitting/receiving a data

dump

Data dumps are transmitted and received on the

MIDI channel specified by the Global mode MIDI

Ch setting. Data dumps can be transmitted manu-

ally as described below, and are also transmitted

in response to a Data Dump Request message of

the appropriate type.

MIDI DUMP ........... PtBnkA...D, AllSng, Global

Transmitting

Here’s how to transmit an ESX-1 system exclusive

data dump (pattern, song, or global mode settings)

from MIDI OUT to a connected MIDI data filer or

computer.

1. Connect the ESX-1’s MIDI OUT connector to the

MIDI IN connector of an external MIDI device that

is able to receive the MIDI data dump (e.g., another

ESX-1, a MIDI data filer, or a personal computer

that is running a MIDI data management program).

2. Set your external MIDI device and the ESX-1 to the

same MIDI channel. If you are transmitting to a

MIDI data filer, you do not normally need to set

the MIDI channel to match.

3. Press the Global key (the key will light).

4. Hold down the shift key and press step key 15

(MIDI UTILITY) (key 15 will light). The parameter

display will indicate “MIDIUtil.”

5. The value display will indicate “Filter.” Turn the

dial to change this to “Dump,” and press key 15.

6. The parameter display will indicate “MIDIDump.”

The value display will read “(data to be transmit-

ted).” Turn the dial to select the data that you want

to transmit.

PtBnkA: pattern bank A data (A01...64)

PtBnkB: pattern bank B data (B01...64)

PtBnkC: pattern bank C data (C01...64)

PtBnkD: pattern bank D data (D01...64)

AllSng: all song data

Global: global data

7. Press key 15 once again to transmit the data. If you

decide to cancel before you have begun transmis-

sion, press the STOP/CANCEL key.

Receiving

Here’s how to receive an ESX-1 system exclusive

data dump from an external MIDI data filer or com-

puter connected to the ESX-1’s MIDI IN connector.

If the Global mode Protect setting is “On,” MIDI data

dump reception is disabled except when you are in

Global mode.

1. Connect the MIDI OUT connector of the external

MIDI device that will transmit the data dump (an-

other ESX-1, a MIDI data filer, or a personal com-

puter that is running a MIDI data management

program) to the MIDI IN connector of the ESX-1.

2. Set your external MIDI device and the ESX-1 to the

same MIDI channel (the keyboard part 1 setting on

the ESX-1). If you are transmitting data from a data

filer, use the same channel setting as when you

saved the data.

3. Press the Global key (the key will light).

4. Hold down the shift key and press step key 15

(MIDI UTILITY) (key 15 will light). The parameter

display will indicate “MIDIUtil.”

5. The value display will indicate “Filter.” Turn the

dial to change this to “Dump,” and then press key

15.

6. The parameter display will indicate “MIDIDump.”

Operate the external device to make it transmit the

data dump to the ESX-1.

For details on data dumps, refer to the ESX-1’s MIDI

implementation. If you wish to obtain the MIDI imple-

mentation, please contact Korg distributor.

Do not touch the ESX-1’s keys while a data dump

is being executed. While you are using the Dump

function, the ESX-1 can transmit or receive sys-

tem exclusive data even if the MIDI FILTER pa-

rameter “E” is set to “x.”

When the ESX-1 receives a data dump, it will take

up to ten seconds for the data to be written into

memory (the Write/Rename key will light). Never

turn off the ESX-1’s power while this is occurring.

Doing so may destroy the data. Also, new MIDI data

cannot be received during this time. When receiv-

ing two or more data dumps into the ESX-1, you

must allow an appropriate interval of time between

each data dump.

Switching patterns

When you switch patterns, the ESX-1 will transmit a pro-

gram change message [Cn, pp] (and Bank Select [Bn, 00, mm]

(control change #00), [Bn, 20, bb] (control change #32) (mm:

bank number upper byte, bb: bank number lower byte).

If the ESX-1 receives a program change message on the ap-

propriate MIDI channel, it will switch patterns within the

same group (e.g., from A01 to A02). If the ESX-1 receives a

bank select message, it will switch groups (e.g., from A01

to C01) so that patterns of another group can be selected.

The MIDI mode MIDI Filter setting determines whether the

ESX-1 will transmit and receive program changes.

Bank select

Program change Pattern number

MSB LSB

00 00 0–127 A01–B64

00 01 0–127 C01–D64

Missbrauch melden von Frage und/oder Antwort

Libble nimmt den Missbrauch seiner Dienste sehr ernst. Wir setzen uns dafür ein, derartige Missbrauchsfälle gemäß den Gesetzen Ihres Heimatlandes zu behandeln. Wenn Sie eine Meldung übermitteln, überprüfen wir Ihre Informationen und ergreifen entsprechende Maßnahmen. Wir melden uns nur dann wieder bei Ihnen, wenn wir weitere Einzelheiten wissen müssen oder weitere Informationen für Sie haben.

Korg Electribe ESX-1 Seite 92

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Missbrauch melden von Frage und/oder Antwort

Art des Missbrauchs:

Forenregeln

Neu registrieren

Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Ihre Frage wurde zu diesem Forum hinzugefügt

Info