Bedienungsanleitung Korg ESX-1 (Seite 69 von 108) (Englisch)

500314

Zoom out

Zoom in

Vorherige Seite

1/108

Nächste Seite

5. Pattern mode

Recording a motion sequence

Here’s how to record a motion sequence (knob or key movements) for a part or

effect.

To record a motion sequence for a part, select the desired part, and

then turn on the motion sequence key of the part common section to

select either SMOOTH or TRIG HOLD.

To record a motion sequence for an effect, turn on the motion se-

quence key of the effect section.

In the following example we will record a motion sequence for the

pitch of a drum part.

If you re-record a knob for which a motion sequence has already

been recorded, the previous data will be erased.

1. In Pattern mode, select the pattern that you want to edit.

2. Press a drum part key to select the part that you want to edit.

3. Press the motion sequence key to select either SMOOTH or TRIG

HOLD.

4. Press the REC key to enter record-ready mode. The REC key will

light and the PLAY/PAUSE key will blink.

5. Press the PLAY/PAUSE key to start the pattern. The REC key and

PLAY/PAUSE key will light.

6. Move the pitch knob as desired until the pattern completes one cycle.

7. When the pattern has played for exactly one cycle after you began

moving the knob, the REC key will automatically go dark and the

pattern will resume playing back, allowing you to hear the motion

sequence that you recorded.

After recording a motion sequence, you can edit it by pressing the

STEP EDIT key and using MOTION DEST. and MOTION VALUE.

(☞p.70 “Editing motion sequence data”)

If you press the STOP/CANCEL key to stop playback and then save

the pattern as described in “Saving a pattern,” the motion sequence

data you recorded will be saved together with the pattern.

You can record a maximum of twenty-four motion sequences in each

pattern.

TRIG HOLD is the only motion sequence available for the accent

part.

Playing a motion sequence

You can play back a motion sequence in one of the two modes described below.

The playback mode can be selected independently for each part.

Effect motion sequences will always play back using the SMOOTH mode of a part

motion sequence. Motion sequences for an accent part will always play back using

the TRIG HOLD mode.

AMP EG, ROLL, REVERSE, FX SELECT, FX SEND, MOD TYPE,

MOD DEST, BPM SYNC, and FILTER TYPE motion sequences will

always play back using TRIG HOLD even if SMOOTH is selected.

MOTION SEQ ........................................................................

SMOOTH: Knob movements will be played back smoothly, you will

here the effect of the knob being turned even as a single note

is sustained.

TRIG HOLD (trigger hold): Each new note being triggered will “hold”

the motion sequence knob value as it was when the note

was first triggered.

If the motion sequence LED is dark (off), this setting does nothing.

891011 12 13 14 15 16

On On On On On On On On

891011 12 13 14 15 1

On On On On On On On On

891011 12 13 14 15 16

On On On On On On On On

Playback the motion sequence

with Trig Hold setting

Knob movements when the motion

sequence was recorded

Playback the motion sequence

with Smooth setting

STOP/CANCEL

REC

PLAY/PAUSE

Missbrauch melden von Frage und/oder Antwort

Libble nimmt den Missbrauch seiner Dienste sehr ernst. Wir setzen uns dafür ein, derartige Missbrauchsfälle gemäß den Gesetzen Ihres Heimatlandes zu behandeln. Wenn Sie eine Meldung übermitteln, überprüfen wir Ihre Informationen und ergreifen entsprechende Maßnahmen. Wir melden uns nur dann wieder bei Ihnen, wenn wir weitere Einzelheiten wissen müssen oder weitere Informationen für Sie haben.

Korg ESX-1 Seite 69

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Missbrauch melden von Frage und/oder Antwort

Art des Missbrauchs:

Forenregeln

Neu registrieren

Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Ihre Frage wurde zu diesem Forum hinzugefügt

Info