500314
80
Zoom out
Zoom in
Vorherige Seite
1/108
Nächste Seite
80
Erasing data from a song
CLEAR SONG .........................................................................
1.
If the ESX-1 is playing, press the STOP/CANCEL key to stop playback.
2. Hold down the shift key and press step key 10 (CLEAR SONG). (Key
11 will blink.)
3. Press step key 10 once again to erase the data from the song. If you
decide to cancel, press the STOP/CANCEL key.
If you erase song data by accident
Turn the dial to re-select that song without saving it, and you will
revert to the data that was previously saved.
Changing the pattern in a specific position
1. If the ESX-1 is playing, press the STOP/CANCEL key to stop playback.
2. Use the [ ]/[ ] cursor keys to select “Position” in the display.
3. Use the dial to select the position whose pattern you want to change.
4. Press the [ ] cursor key until the display reads “Pattern.”
5.
Use the dial to select the pattern that you want to assign to that posi-
tion. If you want to listen to the selected pattern to hear whether it is
the one you want, press the Pattern mode key to enter Pattern mode,
and play it. To return to Song mode, press the STOP/CANCEL key to
stop playback and then press the Song mode key.
Maintaining the part mute settings even
when the pattern changes
This function applies the current part mute settings to the entire song.
MUTE HOLD ................................................................Off, On
1.
Press the [ ] cursor key until the parameter display reads “MuteHold.”
2. Turn the dial to make the desired setting.
Off: The part mute settings specified within each pattern will be
applied as the position within the song changes during play-
back. However if you change the position but the pattern is
still the same, the part mute settings will be maintained.
On: The part mute status will not change even if the position
moves to a different pattern. However at the beginning of
the song the part mute status will be as specified by the pat-
tern selected for position 1.
Playing back songs in succession
NEXT SONG .................................................. Off, S.01...S.64
When one song finishes playing, this function immediately contin-
ues playback with the next specified song.
1.
Press the [ ] cursor key until the parameter display reads “NextSong.”
2. Turn the dial to select which song will play back following the cur-
rent song. If you select Off, playback will stop when the current song
finishes playing.
If you perform event recording etc. while a song is playing, the speci-
fied NEXT SONG setting will be ignored.
The NEXT SONG setting is ignored when playing back in synchroni-
zation with MIDI Clock messages sent from an external device. The
ESX-1 will obey Song Select messages [F3, ss] (ss: song number)
sent from the external device.
(p.81 “Event recording”)
80

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Forenregeln

Missbrauch melden von Frage und/oder Antwort

Libble nimmt den Missbrauch seiner Dienste sehr ernst. Wir setzen uns dafür ein, derartige Missbrauchsfälle gemäß den Gesetzen Ihres Heimatlandes zu behandeln. Wenn Sie eine Meldung übermitteln, überprüfen wir Ihre Informationen und ergreifen entsprechende Maßnahmen. Wir melden uns nur dann wieder bei Ihnen, wenn wir weitere Einzelheiten wissen müssen oder weitere Informationen für Sie haben.

Art des Missbrauchs:

Zum Beispiel antisemitische Inhalte, rassistische Inhalte oder Material, das zu einer Gewalttat führen könnte.

Beispielsweise eine Kreditkartennummer, persönliche Identifikationsnummer oder unveröffentlichte Privatadresse. Beachten Sie, dass E-Mail-Adressen und der vollständige Name nicht als private Informationen angesehen werden.

Forenregeln

Um zu sinnvolle Fragen zu kommen halten Sie sich bitte an folgende Spielregeln:

Neu registrieren

Registrieren auf E - Mails für Korg ESX-1 wenn:


Sie erhalten eine E-Mail, um sich für eine oder beide Optionen anzumelden.


Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Wenn Sie innerhalb von 15 Minuten keine E-Mail mit dem Handbuch erhalten haben, kann es sein, dass Sie eine falsche E-Mail-Adresse eingegeben haben oder dass Ihr ISP eine maximale Größe eingestellt hat, um E-Mails zu erhalten, die kleiner als die Größe des Handbuchs sind.

Ihre Frage wurde zu diesem Forum hinzugefügt

Möchten Sie eine E-Mail erhalten, wenn neue Antworten und Fragen veröffentlicht werden? Geben Sie bitte Ihre Email-Adresse ein.



Info