Bedienungsanleitung Korg ESX-1 (Seite 93 von 108) (Englisch)

500314

Zoom out

Zoom in

Vorherige Seite

1/108

Nächste Seite

7. Global mode

Setting the pitch bend range

When the ESX-1 receives a pitch bend message [En, vv, vv]

(vv, vv: lower and upper bytes of the value, together express-

ing a range of 16384 steps with 8192 [vv,vv=00H, 40H]), pitch

bend will be applied to the keyboard part receiving on that

channel.

To set the pitch bend range

BEND RANGE .................................. -12...12

1. Press the GLOBAL key (the key will light).

2. Hold down the SHIFT key and press step key 15

(MIDI UTILITY) (key 15 will blink). The param-

eter display will indicate "MIDIUtil."

3. Turn the dial to make the value display indicate

"BndRng," and press key 15.

4. The parameter display will indicate "BendRnge,"

and the value display will indicate the pitch bend

width.

5. Turn the dial to select the pitch bend range. +/-1 is

a semitone, +/-2 is a whole tone, +/-7 is a fifth,

and +/-12 is an octave.

For some sounds, you may be unable to bend the

pitch upward by the full amount specified here.

6. When you have finished making the setting, press

key 15 to return to Global mode (key 15 will go

dark and the GLOBAL key will light).

If you decide to cancel mid-way through this pro-

cedure, press the STOP/CANCEL key or any mode

key.

Synchronizing playback with

an external MIDI device

You can synchronize the tempo of the ESX-1 to the tempo

of an external MIDI device that is able to send or receive

MIDI clock data.

For details on synchronization settings on your external MIDI

device, refer to the manual for that device.

We recommend that you use the ESX-1 as the mas-

ter.

CLOCK ......................................Int, Ext, Auto

Int: The ESX-1 will be the master; the exter-

nal MIDI device will synchronize to it.

Ext: The external MIDI device will be the

master; the ESX-1 will synchronize to it.

Auto: If MIDI clock messages are being received

from a connected external MIDI device,

the ESX-1 will automatically operate with

the “Ext” setting. Otherwise it will oper-

ate with the “Int” setting.

To use the ESX-1 as the master, and synchronize an ex-

ternal MIDI device to it

1. Use a MIDI cable to connect the ESX-1’s MIDI OUT

connector to the MIDI IN connector of your exter-

nal MIDI device (e.g., sequencer or sound module).

2. Press the Global key (it will light).

3. Press the [

] cursor key to change the display to

read “Clock.”

4. Turn the dial to select “Int” (internal clock).

5. Make settings on your external MIDI device (slave)

so that it will receive MIDI clock messages.

6. When you start playback on the ESX-1, the exter-

nal MIDI device will operate in synchronization

with it.

When you use RESET/PLAY to play back from the

beginning of the pattern, only the MIDI Start mes-

sage will be transmitted.

To use the external MIDI device as the master, and syn-

chronize the ESX-1 to it

1. Use a MIDI cable to connect the ESX-1’s MIDI IN

connector to the MIDI OUT connector of your ex-

ternal MIDI device (e.g., sequencer or synthesizer).

2. Press the Global key (it will light).

3. Press the [

] cursor key to change the display to

read “Clock.”

4. Turn the dial to select “Ext” (external clock).

Missbrauch melden von Frage und/oder Antwort

Libble nimmt den Missbrauch seiner Dienste sehr ernst. Wir setzen uns dafür ein, derartige Missbrauchsfälle gemäß den Gesetzen Ihres Heimatlandes zu behandeln. Wenn Sie eine Meldung übermitteln, überprüfen wir Ihre Informationen und ergreifen entsprechende Maßnahmen. Wir melden uns nur dann wieder bei Ihnen, wenn wir weitere Einzelheiten wissen müssen oder weitere Informationen für Sie haben.

Korg ESX-1 Seite 93

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Missbrauch melden von Frage und/oder Antwort

Art des Missbrauchs:

Forenregeln

Neu registrieren

Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Ihre Frage wurde zu diesem Forum hinzugefügt

Info